HP Tc2120 HP Server tc2120 Network Operating System - Installation Guide - Page 69

Boot Loader Installation, Kernel Parameters, GRUB Password, Network Configuration - firewall

Get HP Tc2120 - Server - 256 MB RAM PDF manuals and user guides
UPC - 808736945332
View all HP Tc2120 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 69 highlights

NOTE: If you get a message that says, "The partition table on device xyz was unreadable... click Yes as many times as this message pops up. Boot Loader Installation • GRUB is selected as the default linux bootloader. If this is acceptable, press Next to continue. • HP recommends that you select Configure advanced boot loader options if you have IDE and SCSI drives in the system, or if you have a Promise FastTrak present in the system. You may need to do this and then select Change Drive Order to ensure that the drive you will be booting from is at the top. If you proceed further without making this change, your system might not boot properly. Kernel Parameters After selecting Configure advanced boot loader options, (and if you have a Promise FastTrak present in the system) enter: ide0=0x1f0,0x3f6,14 ide1=0x170,0x376,15 ide2=0 ide3=0 ide4=0 ide5=0 ide6=0 ide7=0 ide8=0 ide9=0 NOTE: Depending upon which storage deice you will be booting from, will determine if you should install the bootloader record on the (MBR) Master Boot Record. Please refer to the Redhat Manuals for further information regarding installing the bootloader. GRUB Password • HP recommends a password to protect access to GRUB. Click Next to continue. Network Configuration NOTE: The network settings need to be customized to your environment. Please refer to Red Hat manuals should you need further details on the networking settings. Firewall Configuration • Review the Firewall setting and modify if necessary. 69

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
NOTE:
If you get a message that says, “The partition table on device xyz was unreadable…
click
Yes
as many times as this message pops up.
Boot Loader Installation
•
GRUB is selected as the default linux bootloader. If this is acceptable, press
Next
to continue.
•
HP recommends that you select
Configure advanced boot loader options
if you
have IDE and SCSI drives in the system, or if you have a Promise FastTrak
present in the system. You may need to do this and then select
Change Drive
Order
to ensure that the drive you will be booting from is at the top. If you
proceed further without making this change, your system might not boot
properly
.
Kernel Parameters
After selecting
Configure advanced boot loader options
, (and if you have a
Promise FastTrak present in the system) enter:
ide0=0x1f0,0x3f6,14 ide1=0x170,0x376,15 ide2=0 ide3=0 ide4=0
ide5=0 ide6=0 ide7=0 ide8=0 ide9=0
NOTE:
Depending upon which storage deice you will be booting from, will determine if you
should install the bootloader record on the (MBR) Master Boot Record. Please refer to the
Redhat Manuals for further information regarding installing the bootloader.
GRUB Password
•
HP recommends a password to protect access to GRUB. Click
Next
to continue.
Network Configuration
NOTE:
The network settings need to be customized to your environment. Please refer to Red
Hat manuals should you need further details on the networking settings.
Firewall Configuration
•
Review the Firewall setting and modify if necessary.
69