IBM 7379E2U User Manual - Page 120

Clear System Event Log, Clear Power-on Password

Get IBM 7379E2U PDF manuals and user guides View all IBM 7379E2U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 120 highlights

Important: If the system-error LED on the front of the server is lit but there are no other error indications, clear the system-event log and shutdown the server. Also, after you complete a repair or correct an error, clear the system-event log to turn off the system-error LED on the front of the server. - POST Event Viewer Select this choice to enter the POST event viewer to view the error messages in the POST event log. - System Event Log Select this choice to view the error messages in the system-event log. - Clear System Event Log Select this choice to clear the system-event log. v User Security Select this choice to set, change, or clear passwords. See "Passwords" on page 105 for more information. This choice is on the full and limited Setup utility menu. - Set Power-on Password Select this choice to set or change a power-on password. For more information, see "Power-on password" on page 105. - Clear Power-on Password Select this choice to clear a power-on password. For more information, see "Power-on password" on page 105. - Set Administrator Password Select this choice to set or change an administrator password. An administrator password is intended to be used by a system administrator; it limits access to the full Setup utility menu. If an administrator password is set, the full Setup utility menu is available only if you type the administrator password at the password prompt. For more information, see "Administrator password" on page 106. Attention: If you set an administrator password and then forget it, there is no way to change, override, or remove it. You must replace the system board. - Clear Administrator Password Select this choice to clear an administrator password. For more information, see "Administrator password" on page 106. 104 IBM System x3400 M3 Type 7378/7379: Installation and User's Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
Important:
If the system-error LED on the front of the server is lit but there are
no other error indications, clear the system-event log and shutdown the server.
Also, after you complete a repair or correct an error, clear the system-event log
to turn off the system-error LED on the front of the server.
–
POST Event Viewer
Select this choice to enter the POST event viewer to view the error messages
in the POST event log.
–
System Event Log
Select this choice to view the error messages in the system-event log.
–
Clear System Event Log
Select this choice to clear the system-event log.
v
User Security
Select this choice to set, change, or clear passwords. See “Passwords” on page
105 for more information.
This choice is on the full and limited Setup utility menu.
–
Set Power-on Password
Select this choice to set or change a power-on password. For more
information, see “Power-on password” on page 105.
–
Clear Power-on Password
Select this choice to clear a power-on password. For more information, see
“Power-on password” on page 105.
–
Set Administrator Password
Select this choice to set or change an administrator password. An
administrator password is intended to be used by a system administrator; it
limits access to the full Setup utility menu. If an administrator password is set,
the full Setup utility menu is available only if you type the administrator
password at the password prompt. For more information, see “Administrator
password” on page 106.
Attention:
If you set an administrator password and then forget it, there is
no way to change, override, or remove it. You must replace the system board.
–
Clear Administrator Password
Select this choice to clear an administrator password. For more information,
see “Administrator password” on page 106.
104
IBM System x3400 M3 Type 7378/7379: Installation and User's Guide