IBM 865741Y Handbook - Page 131
Completing the Installation
 |
View all IBM 865741Y manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 131 highlights
Completing the Installation Completing the Installation Before you begin: Complete all the installation procedures for the internal options that you have chosen to install. Read "Electrical Safety" on page 54. 1. Ensure that all components have been reassembled correctly and that no tools or loose screws are left inside your server. 2. Clear any cables that might impede the replacement of the cover. 3. Install the side cover: a. Align the top and bottom cover tabs with the corresponding notches on the frame of the server. b. Slide the side cover to the rear, as shown in the following illustration. Make sure that the cover is latched into position. Chapter 4. Installing Options 113
-
1 -
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126 -
127 -
128 -
129 -
130 -
131 -
132 -
133 -
134 -
135 -
136 -
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179
-
180
-
181
-
182
-
183
-
184
-
185
-
186
-
187
-
188
-
189
-
190
-
191
-
192
-
193
-
194
-
195
-
196
-
197
-
198
-
199
-
200
-
201
-
202
-
203
-
204
-
205
-
206
-
207
-
208
-
209
-
210
-
211
-
212
-
213
-
214
-
215
-
216
-
217
-
218
-
219
-
220
-
221
-
222
-
223
-
224
-
225
-
226
-
227
-
228
-
229
-
230
-
231
-
232
-
233
-
234
-
235
-
236
-
237
-
238
-
239
-
240
-
241
-
242
-
243
-
244
-
245
-
246
-
247
-
248
-
249
-
250
-
251
-
252
-
253
-
254
-
255
-
256
-
257
-
258
-
259
-
260
-
261
-
262
-
263
-
264
-
265
-
266
-
267
-
268
-
269
-
270
-
271
-
272
-
273
-
274
-
275
-
276
-
277
-
278
-
279
-
280
-
281
-
282
-
283
-
284
-
285
-
286
-
287
-
288
-
289
-
290
-
291
-
292
-
293
-
294
 |
 |
Completing the Installation
Completing the Installation
Before you begin:
±
Complete all the installation procedures for the internal
options that you have chosen to install.
±
Read “Electrical Safety” on page
54.
1.
Ensure that all components have been reassembled correctly and
that no tools or loose screws are left inside your server.
2.
Clear any cables that might impede the replacement of the
cover.
3.
Install the side cover:
a.
Align the top and bottom cover tabs with the corresponding
notches on the frame of the server.
b.
Slide the side cover to the rear, as shown in the following
illustration.
Make sure that the cover is latched into
position.
Chapter 4.
Installing Options
113