IBM HC10 Service Guide - Page 32

Removing, blade, workstation, BladeCenter - + workstation blade

Get IBM HC10 - BladeCenter - 7996 PDF manuals and user guides
UPC - 883436017671
View all IBM HC10 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

Removing the blade workstation from a BladeCenter unit Attention: v To maintain proper system cooling, do not operate the BladeCenter unit without a blade workstation, blade server, expansion unit, or blade filler installed in each blade bay. v Note the bay number. Reinstalling a blade workstation into a different bay than the one from which it was removed could have unintended consequences. Some configuration information and update options are established according to bay number; if you reinstall the blade workstation into a different bay, you might have to reconfigure the blade workstation. To remove the blade workstation from a BladeCenter unit, complete the following steps. The appearance of your BladeCenter unit might be different, see the documentation for your BladeCenter unit for additional information. Release handles (open) 1. Read the safety information that begins on page vii and "Installation guidelines" on page 13. 2. (BladeCenter T and HT units only) Remove the bezel assembly on the BladeCenter T or HT unit. For detailed instructions for removing the bezel assembly, see the Installation and User's Guide that comes with the BladeCenter T or HT unit. 3. If the blade workstation is operating, shut down the operating system; then, press the power-control button (behind the blade workstation control panel door) to turn off the blade workstation (see "Turning off the blade workstation" on page 6 for more information). Attention: Wait at least 30 seconds, until the hard disk drives stop spinning, before proceeding to the next step. 4. Pull the two release handles to the open position as shown in the illustration. The blade workstation moves out of the bay approximately 0.6 cm (0.25 inch). 5. Pull the blade workstation out of the bay. 6. Place either a blade filler or another blade workstation in the bay within 1 minute. 16 BladeCenter HC10 Type 7996: Problem Determination and Service Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
Removing
the
blade
workstation
from
a
BladeCenter
unit
Attention:
v
To
maintain
proper
system
cooling,
do
not
operate
the
BladeCenter
unit
without
a
blade
workstation,
blade
server,
expansion
unit,
or
blade
filler
installed
in
each
blade
bay.
v
Note
the
bay
number.
Reinstalling
a
blade
workstation
into
a
different
bay
than
the
one
from
which
it
was
removed
could
have
unintended
consequences.
Some
configuration
information
and
update
options
are
established
according
to
bay
number;
if
you
reinstall
the
blade
workstation
into
a
different
bay,
you
might
have
to
reconfigure
the
blade
workstation.
To
remove
the
blade
workstation
from
a
BladeCenter
unit,
complete
the
following
steps.
The
appearance
of
your
BladeCenter
unit
might
be
different,
see
the
documentation
for
your
BladeCenter
unit
for
additional
information.
Release handles
(open)
1.
Read
the
safety
information
that
begins
on
page
vii
and
“Installation
guidelines”
on
page
13.
2.
(BladeCenter
T
and
HT
units
only)
Remove
the
bezel
assembly
on
the
BladeCenter
T
or
HT
unit.
For
detailed
instructions
for
removing
the
bezel
assembly,
see
the
Installation
and
User’s
Guide
that
comes
with
the
BladeCenter
T
or
HT
unit.
3.
If
the
blade
workstation
is
operating,
shut
down
the
operating
system;
then,
press
the
power-control
button
(behind
the
blade
workstation
control
panel
door)
to
turn
off
the
blade
workstation
(see
“Turning
off
the
blade
workstation”
on
page
6
for
more
information).
Attention:
Wait
at
least
30
seconds,
until
the
hard
disk
drives
stop
spinning,
before
proceeding
to
the
next
step.
4.
Pull
the
two
release
handles
to
the
open
position
as
shown
in
the
illustration.
The
blade
workstation
moves
out
of
the
bay
approximately
0.6
cm
(0.25
inch).
5.
Pull
the
blade
workstation
out
of
the
bay.
6.
Place
either
a
blade
filler
or
another
blade
workstation
in
the
bay
within
1
minute.
16
BladeCenter
HC10
Type
7996:
Problem
Determination
and
Service
Guide