IBM HC10 Service Guide - Page 45

Installing, graphics

Get IBM HC10 - BladeCenter - 7996 PDF manuals and user guides
UPC - 883436017671
View all IBM HC10 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

Installing a graphics card To install a replacement graphics card, complete the following steps. Graphics card Release latch 1. Touch the static-protective package that contains the expansion card to any unpainted metal surface on the BladeCenter unit or any unpainted metal surface on any other grounded rack component; then, remove the expansion card from the package. 2. Orient the graphics card over the system board and slide the narrow end of the card into the graphics-card connector. 3. Lower the release latch to secure the graphics card to the system board. Note: For device-driver and configuration information to complete the installation of the graphics card, see the documentation that comes with the graphics card. 4. Install the blade workstation cover (see "Installing the blade workstation cover" on page 20). 5. Install the blade workstation into the BladeCenter unit (see "Installing the blade workstation in a BladeCenter unit" on page 17). Chapter 4. Removing and replacing blade workstation components 29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
Installing
a
graphics
card
To
install
a
replacement
graphics
card,
complete
the
following
steps.
Graphics
card
Release
latch
1.
Touch
the
static-protective
package
that
contains
the
expansion
card
to
any
unpainted
metal
surface
on
the
BladeCenter
unit
or
any
unpainted
metal
surface
on
any
other
grounded
rack
component;
then,
remove
the
expansion
card
from
the
package.
2.
Orient
the
graphics
card
over
the
system
board
and
slide
the
narrow
end
of
the
card
into
the
graphics-card
connector.
3.
Lower
the
release
latch
to
secure
the
graphics
card
to
the
system
board.
Note:
For
device-driver
and
configuration
information
to
complete
the
installation
of
the
graphics
card,
see
the
documentation
that
comes
with
the
graphics
card.
4.
Install
the
blade
workstation
cover
(see
“Installing
the
blade
workstation
cover”
on
page
20).
5.
Install
the
blade
workstation
into
the
BladeCenter
unit
(see
“Installing
the
blade
workstation
in
a
BladeCenter
unit”
on
page
17).
Chapter
4.
Removing
and
replacing
blade
workstation
components
29