IBM HC10 Service Guide - Page 36

Installing, blade, workstation, cover

Get IBM HC10 - BladeCenter - 7996 PDF manuals and user guides
UPC - 883436017671
View all IBM HC10 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

Installing the blade workstation cover To install the blade workstation cover, complete the following steps. Statement 21: CAUTION: Hazardous energy is present when the blade workstation is connected to the power source. Always replace the blade cover before installing the blade workstation. Cover pins Blade-cover release Blade-cover release Attention: You cannot insert the blade workstation into the BladeCenter unit until the cover is installed and closed. Do not attempt to override this protection. 1. Read the safety information that begins on page vii and "Installation guidelines" on page 13. 2. Lower the cover so that the slots at the rear slide down onto the pins at the rear of the blade workstation. Before closing the cover, check that all components are installed and seated correctly and that you have not left loose tools or parts inside the blade workstation. 3. Pivot the cover to the closed position until it clicks into place. 4. Install the blade workstation into the BladeCenter unit (see "Installing the blade workstation in a BladeCenter unit" on page 17 for instructions). 20 BladeCenter HC10 Type 7996: Problem Determination and Service Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
Installing
the
blade
workstation
cover
To
install
the
blade
workstation
cover,
complete
the
following
steps.
Statement
21:
CAUTION:
Hazardous
energy
is
present
when
the
blade
workstation
is
connected
to
the
power
source.
Always
replace
the
blade
cover
before
installing
the
blade
workstation.
Blade-cover
release
Blade-cover
release
Cover
pins
Attention:
You
cannot
insert
the
blade
workstation
into
the
BladeCenter
unit
until
the
cover
is
installed
and
closed.
Do
not
attempt
to
override
this
protection.
1.
Read
the
safety
information
that
begins
on
page
vii
and
“Installation
guidelines”
on
page
13.
2.
Lower
the
cover
so
that
the
slots
at
the
rear
slide
down
onto
the
pins
at
the
rear
of
the
blade
workstation.
Before
closing
the
cover,
check
that
all
components
are
installed
and
seated
correctly
and
that
you
have
not
left
loose
tools
or
parts
inside
the
blade
workstation.
3.
Pivot
the
cover
to
the
closed
position
until
it
clicks
into
place.
4.
Install
the
blade
workstation
into
the
BladeCenter
unit
(see
“Installing
the
blade
workstation
in
a
BladeCenter
unit”
on
page
17
for
instructions).
20
BladeCenter
HC10
Type
7996:
Problem
Determination
and
Service
Guide