IBM HC10 Service Guide - Page 53

Installing, system, board, assembly

Get IBM HC10 - BladeCenter - 7996 PDF manuals and user guides
UPC - 883436017671
View all IBM HC10 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 53 highlights

Installing the system board assembly To install the system board assembly, complete the following steps: 1. Install all of the components in the following list that were removed from the old system board assembly onto the new system board assembly. v Microprocessor and heat sink. See "Installing a microprocessor and heat sink" on page 34. v Hard disk drive. See "Installing a SATA storage drive" on page 23. v DIMMs. See "Installing a memory module" on page 24. v Graphics card. See "Installing a graphics card" on page 29. v Compression card. See "Installing a compression card" on page 27. 2. Install the bezel assembly (see "Installing the bezel assembly" on page 21). 3. Install the blade workstation cover (see "Installing the blade workstation cover" on page 20). 4. Install the blade workstation into the BladeCenter unit (see "Installing the blade workstation in a BladeCenter unit" on page 17). Chapter 4. Removing and replacing blade workstation components 37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
Installing
the
system
board
assembly
To
install
the
system
board
assembly,
complete
the
following
steps:
1.
Install
all
of
the
components
in
the
following
list
that
were
removed
from
the
old
system
board
assembly
onto
the
new
system
board
assembly.
v
Microprocessor
and
heat
sink.
See
“Installing
a
microprocessor
and
heat
sink”
on
page
34.
v
Hard
disk
drive.
See
“Installing
a
SATA
storage
drive”
on
page
23.
v
DIMMs.
See
“Installing
a
memory
module”
on
page
24.
v
Graphics
card.
See
“Installing
a
graphics
card”
on
page
29.
v
Compression
card.
See
“Installing
a
compression
card”
on
page
27.
2.
Install
the
bezel
assembly
(see
“Installing
the
bezel
assembly”
on
page
21).
3.
Install
the
blade
workstation
cover
(see
“Installing
the
blade
workstation
cover”
on
page
20).
4.
Install
the
blade
workstation
into
the
BladeCenter
unit
(see
“Installing
the
blade
workstation
in
a
BladeCenter
unit”
on
page
17).
Chapter
4.
Removing
and
replacing
blade
workstation
components
37