IBM HC10 Service Guide - Page 47

recommended

Get IBM HC10 - BladeCenter - 7996 PDF manuals and user guides
UPC - 883436017671
View all IBM HC10 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

Statement 2: CAUTION: When replacing the lithium battery, use only IBM Part Number 15F8409 or an equivalent type battery recommended by the manufacturer. If your system has a module containing a lithium battery, replace it only with the same module type made by the same manufacturer. The battery contains lithium and can explode if not properly used, handled, or disposed of. Do not: v Throw or immerse into water v Heat to more than 100°C (212°F) v Repair or disassemble Dispose of the battery as required by local ordinances or regulations. Note: See "Battery return program" on page 89 for more information. To install the battery, complete the following steps. 1. Follow any special handling and installation instructions that come with the battery. 2. Insert the battery: a. Tilt the battery so that you can insert it into the socket on the side opposite the battery clip. b. Press the battery down into the socket until it clicks into place. Make sure the battery clip holds the battery securely. 3. Install the blade workstation cover (see "Installing the blade workstation cover" on page 20). 4. Install the blade workstation into the BladeCenter unit (see "Installing the blade workstation in a BladeCenter unit" on page 17). 5. Turn on the blade workstation and run the Configuration/Setup Utility program. Set configuration parameters as needed (see "Using the Configuration/Setup Utility program" on page 9 for information). Chapter 4. Removing and replacing blade workstation components 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
Statement
2:
CAUTION:
When
replacing
the
lithium
battery,
use
only
IBM
Part
Number
15F8409
or
an
equivalent
type
battery
recommended
by
the
manufacturer.
If
your
system
has
a
module
containing
a
lithium
battery,
replace
it
only
with
the
same
module
type
made
by
the
same
manufacturer.
The
battery
contains
lithium
and
can
explode
if
not
properly
used,
handled,
or
disposed
of.
Do
not:
v
Throw
or
immerse
into
water
v
Heat
to
more
than
100°C
(212°F)
v
Repair
or
disassemble
Dispose
of
the
battery
as
required
by
local
ordinances
or
regulations.
Note:
See
“Battery
return
program”
on
page
89
for
more
information.
To
install
the
battery,
complete
the
following
steps.
1.
Follow
any
special
handling
and
installation
instructions
that
come
with
the
battery.
2.
Insert
the
battery:
a.
Tilt
the
battery
so
that
you
can
insert
it
into
the
socket
on
the
side
opposite
the
battery
clip.
b.
Press
the
battery
down
into
the
socket
until
it
clicks
into
place.
Make
sure
the
battery
clip
holds
the
battery
securely.
3.
Install
the
blade
workstation
cover
(see
“Installing
the
blade
workstation
cover”
on
page
20).
4.
Install
the
blade
workstation
into
the
BladeCenter
unit
(see
“Installing
the
blade
workstation
in
a
BladeCenter
unit”
on
page
17).
5.
Turn
on
the
blade
workstation
and
run
the
Configuration/Setup
Utility
program.
Set
configuration
parameters
as
needed
(see
“Using
the
Configuration/Setup
Utility
program”
on
page
9
for
information).
Chapter
4.
Removing
and
replacing
blade
workstation
components
31