IBM HC10 Service Guide - Page 35

Removing, replacing, blade, workstation, cover

Get IBM HC10 - BladeCenter - 7996 PDF manuals and user guides
UPC - 883436017671
View all IBM HC10 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

Removing and replacing Tier 1 CRUs Replacement of Tier 1 CRUs is your responsibility. If IBM installs a Tier 1 CRU at your request, you will be charged for the installation. The illustrations in this document might differ slightly from your hardware. Removing the blade workstation cover To remove the blade workstation cover, complete the following steps. Cover pins Blade-cover release Blade-cover release 1. Read the safety information that begins on page vii and "Installation guidelines" on page 13. 2. If the blade workstation is installed in a BladeCenter unit, remove it (see "Removing the blade workstation from a BladeCenter unit" on page 16 for instructions). 3. Carefully lay the blade workstation down on a flat, static-protective surface, with the cover side up. 4. Press the blade-cover release on each side of the blade workstation or expansion unit and lift the cover open, as shown in the illustration. 5. Lift the cover from the blade workstation and store it for future use. Chapter 4. Removing and replacing blade workstation components 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
Removing
and
replacing
Tier
1
CRUs
Replacement
of
Tier
1
CRUs
is
your
responsibility.
If
IBM
installs
a
Tier
1
CRU
at
your
request,
you
will
be
charged
for
the
installation.
The
illustrations
in
this
document
might
differ
slightly
from
your
hardware.
Removing
the
blade
workstation
cover
To
remove
the
blade
workstation
cover,
complete
the
following
steps.
Blade-cover
release
Blade-cover
release
Cover
pins
1.
Read
the
safety
information
that
begins
on
page
vii
and
“Installation
guidelines”
on
page
13.
2.
If
the
blade
workstation
is
installed
in
a
BladeCenter
unit,
remove
it
(see
“Removing
the
blade
workstation
from
a
BladeCenter
unit”
on
page
16
for
instructions).
3.
Carefully
lay
the
blade
workstation
down
on
a
flat,
static-protective
surface,
with
the
cover
side
up.
4.
Press
the
blade-cover
release
on
each
side
of
the
blade
workstation
or
expansion
unit
and
lift
the
cover
open,
as
shown
in
the
illustration.
5.
Lift
the
cover
from
the
blade
workstation
and
store
it
for
future
use.
Chapter
4.
Removing
and
replacing
blade
workstation
components
19