Magnavox MDR868H Owners Manual - Page 61

Select Skip Channels using, Select Antenna Out using

Get Magnavox MDR868H PDF manuals and user guides View all Magnavox MDR868H manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

EN Add Channels This function lets you add the Channels that were not added by "Auto Channel Preset" due to the reception conditions during the initial setup. 2 Select "Add Channels" using [ K/ L ], then press [ OK ]. • The password will be required if you have locked Channels. Refer to 'Channel Lock' on page 62. • Channel search will begin. 3 Press [ OK ] on "Finish" to complete Channel scan. • Press [ (EXIT) ] to Exit. Skip Channels The Channels Selected here will be Skipped when Selecting the Channels using [ CH +/− ]. Those Channels can still be Selected using [ the Number buttons ]. 2 Select "Skip Channels" using [ K/ L ], then press [ OK ]. 3 Select the Channel you would like to Skip using [ K/ L ], then press [ OK ]. • "Watch" that the Channel is not Skipped. • "Skip" that the Channel is Skipped. Antenna Out Set whether you want the Antenna signal to passthrough when the Power is Off (Standby) mode. 2 Select "Antenna Out" using [ K/ L ], then press [ OK ]. 3 Select a desired item using [ K/ L ], then press [ OK ]. This unit will passthrough the Antenna signal when the Power is Off (Standby) Old mode. Off This unit does not passthrough the Antenna signal in the Power Off (Standby) mode. • If you connect the RF to another device, recommend to set it "Old". • If you Select "Old", Power Consumption is high. Attenuator To decrease TV Broadcasting signal strength to the proper level. 2 Select "Attenutor" using [ K/ L ], then press [ OK ]. 3 Select a desired item using [ K/ L ], then press [ OK ]. TV Broadcasting signal strength to the Old proper level. Off Maintain the current TV Broadcasting signal strength. • To reactivate a Skipped Channel, use [ K/ L ] then press [ OK ]. • Repeat step 2 until you Select all the Channels you would like to Skip. • Press [ (EXIT) ] to Exit. FUNCTION SETUP Continued on next page. EN - 61

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
EN - 61
FUNCTION SETUP
EN
Add Channels
This function lets you add the Channels that were not added by
“Auto Channel Preset” due to the reception conditions during
the initial setup.
2
Select “Add Channels” using
[
K
/
L
]
, then
press
[ OK ]
.
•
The password will be required if you have locked
Channels. Refer to ‘Channel Lock’ on page 62.
•
Channel search will begin.
3
Press
[ OK ]
on “Finish” to complete
Channel scan.
• Press
[
(EXIT) ]
to Exit.
Skip Channels
The Channels Selected here will be Skipped when Selecting the
Channels using
[ CH +/
−
]
.
Those Channels can still be Selected using
[ the Number
buttons ]
.
2
Select “Skip Channels” using
[
K
/
L
]
, then
press
[ OK ]
.
3
Select the Channel you would like to Skip
using
[
K
/
L
]
, then press
[ OK ]
.
•
“Watch” that the Channel is not Skipped.
•
“Skip” that the Channel is Skipped.
•
To reactivate a Skipped Channel, use
[
K
/
L
]
then
press
[ OK ]
.
•
Repeat step
2
until you Select all the Channels you
would like to Skip.
• Press
[
(EXIT) ]
to Exit.
Antenna Out
Set whether you want the Antenna signal to passthrough when
the Power is Off (Standby) mode.
2
Select “Antenna Out” using
[
K
/
L
]
, then
press
[ OK ]
.
3
Select a desired item using
[
K
/
L
]
, then
press
[ OK ]
.
Old
Off
This unit will passthrough the Antenna
signal when the Power is Off (Standby)
mode.
This unit does not passthrough the
Antenna signal in the Power Off
(Standby) mode.
•
If you connect the RF to another device, recommend
to set it
“Old”.
•
If you Select “Old”, Power Consumption is high.
Attenuator
To decrease TV Broadcasting signal strength to the proper level.
2
Select “Attenutor” using
[
K
/
L
]
, then press
[ OK ]
.
3
Select a desired item using
[
K
/
L
]
, then
press
[ OK ]
.
Old
Off
TV Broadcasting signal strength to the
proper level.
Maintain the current TV Broadcasting
signal strength.
Continued on next page.