Sharp AR M550N Installation Manual - Page 17

Adjust the caster, Connect the connector of the large capacity tray., Select the paper size.

Get Sharp AR M550N - B/W Laser - Copier PDF manuals and user guides View all Sharp AR M550N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

F. Adjust the caster 1) After installing the large capacity tray to the main unit, loosen the screws (one in the front and one in the rear) of the adjustment caster mounting plate attached to the lower side of the large capacity tray. At that time, the casters of the adjustment caster mounting plate are brought into contact with the floor by the spring force. 2) Tighten the screws of the caster mounting plate which were loosened in procedure 1). F side 2) Connect the large capacity tray interface harness connector and the heating heater interface harness connector to the main unit connector, and tighten the connector screw to fix the connector. a b R side H. Select the paper size. (1) Change A4 size to LT size The factory setting of the paper size is A4. To select another size, perform the following procedures. 1) Pull out the large capacity tray until it stops. G. Connect the connector of the large capacity tray. 1) Remove the screw (one for each) from the connector cover on the main unit and then remove the two connector covers. 2) Loosen the stopper fixing screw (1 pc.) on the lower right side of the paper feed tray to disable the stopper function. 3) Then pull out the paper feed tray again until it stops. AR-M550/M620/M700 INSTALLATION MANUAL (AR-LC6) 2 - 4

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
AR-M550/M620/M700
INSTALLATION MANUAL
(AR-LC6)
2 - 4
F.
Adjust the caster
1)
After installing the large capacity tray to the main unit, loosen the
screws (one in the front and one in the rear) of the adjustment
caster mounting plate attached to the lower side of the large
capacity tray.
At that time, the casters of the adjustment caster mounting plate
are brought into contact with the floor by the spring force.
2)
Tighten the screws of the caster mounting plate which were loos-
ened in procedure 1).
G.
Connect the connector of the large capacity tray.
1)
Remove the screw (one for each) from the connector cover on the
main unit and then remove the two connector covers.
2)
Connect the large capacity tray interface harness connector and
the heating heater interface harness connector to the main unit
connector, and tighten the connector screw to fix the connector.
H.
Select the paper size.
(1)
Change A4 size to LT size
The factory setting of the paper size is A4. To select another size, per-
form the following procedures.
1)
Pull out the large capacity tray until it stops.
2)
Loosen the stopper fixing screw (1 pc.) on the lower right side of
the paper feed tray to disable the stopper function.
3)
Then pull out the paper feed tray again until it stops.
F side
R side
a
b