Home » Sharp Manuals » Multifunction Devices » Sharp AR M550N » Manual Viewer

Sharp AR M550N Installation Manual - Page 32

Ar-f15/f16 Unpacking And, Installation

Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

[4] AR-F15/F16 UNPACKING AND INSTALLATION 1. Unpacking When removing or moving, be sure to perform by two persons not to drop the unit. A. Unpacking procedure (1) Removal of the main unit 1) Remove the fixing member and remove the top case. 4) Hold the upper section of the machine with two persons, and pull it up and stand it straight. (The machine is very heavy. Be careful.) 5) Remove the tape and the skid. 2) Remove the packaged parts from the add. 6) Remove the upper add. 3) Check the packaged parts. 1 2 3 5 6 4 7 8 Packaged parts 1 Positioning pin 2 Earth plate 3 Earth mounting plate 4 Rail mounting plate 1 pc. 1 pc. 1 pc. 1 pc. 5 Staple label 6 Screw G (M4 x 6) 7 Screw H (M4 x 10) 8 Screw I (M4 x 18) 2 pcs. 3 pcs. 2 pcs. 4 pcs. AR-M550/M620/M700 INSTALLATION MANUAL (AR-F15/F16) 4 - 1

Section	Page
[1] AR-M550/M620/M700 UNPACKING AND INSTALLATION	2
1. Installing (use) conditions	2
A. Bringing space	2
B. Installing space	2
C. Power source (Capacity, voltage, frequency, safety, plug)	2
D. Floor strength and level	2
E. Direct rays of the sun, dust, temperature, humidity, gasses, chemicals, vibration	2
2. Transit and delivery	3
A. Implements, facility, and manpower	3
B. Delivery	3
3. Unpacking	3
A. Unpacking procedure	3
B. Adjuster cover installation	5
C. Remove the fixing tape and the reinforcing material	5
D. Lock release	6
E. Press the fusing section (upper and lower heat rollers) and remove the process separation pawl...	6
F. Set developer	7
G. Paper supply	8
H. The other parts setting	12
4. Cleaning	12
A. Main charger	12
5. Image quality check	13
A. Focus (Resolution)	13
B. Copy image off-center	13
C. Image loss, void area	13
6. Specifications setting	13
7. Recording of setting and adjustment data	13
8. Preparation for transit	13
[2] AR-LC6 UNPACKING AND INSTALLATION	14
1. Unpacking	14
2. Installation	14
A. Turn off the power of the main unit.	14
B. Attach the upper mounting plates and the lower front/rear connecting plates.	14
C. Fixing material and packaged part removal	15
D. Remove the paper feed base screw of the large capacity tray.	15
E. Attach the large capacity tray to the main unit.	16
F. Adjust the caster	17
G. Connect the connector of the large capacity tray.	17
H. Select the paper size.	17
I. Turn the main power switch on the main unit to the ON position.	19
J. Set the size.	19
K. Carry out the print off center adjustment	20
[3] AR-CF2 UNPACKING AND INSTALLATION	22
1. Unpacking	22
2. Installation	23
[4] AR-F15/F16 UNPACKING AND INSTALLATION	32
1. Unpacking	32
A. Unpacking procedure	32
B. Note for packing	35
2. Installation	35
A. Installation procedure	35
[5] AR-PN4 UNPACKING AND INSTALLATION	39
1. Unpacking	39
(1) Removal of the main unit	39
(2) Removal of the fixing member	39
Packaged parts (accessories)	39
2. Installation	39
[6] AR-P19 INSTALLATION	43
[7] AR-FR11 INSTALLATION	45
[8] AR-PK5 INSTALLATION	47
[9] AR-NS3 INSTALLATION	48
[10] AR-FX8/AR-MM9 INSTALLATION	49
1) Turn off the power switch of the main unit.	49
2) Remove the MFP control PWB.	49
3) Mount an extended memory. Mount an extended memory to the socket located on the back of the FA...	49
4) Attach the FAX interface PWB unit. Connect the FAX interface PWB unit to the FAX interface PWB...	49
5) Connect the FAX interface cable. Connect the FAX interface cable to the MFP control PWB unit.	49
6) Reattach the MFP control PWB unit.	50
7) Reattach the upper right cabinet. Secure the snap band of the FAX interface cable. Then, remov...	50
Pull out the grip of the main unit, pass it through the hole shown in the illustration, then atta...	50
8) Attach the FAX box unit. Among the four screws shown in the illustration that secure the rear ...	50
9) Connect the FAX power connector. Remove the screw that secures the connector cover on the main...	50
10) Connect the FAX interface cable to the FAX box unit. Pass the FAX interface cable behind the ...	50
11) Turn on the main power switch and the power switch of the main unit.	51
12) Set the destination of the main unit.	51
13) Set the destination of the FAX.	51
Destination	51
FAX Software SW No.1 - 8	51
1	51
0	51
1	51
1	51
0	51
1	51
0	51
1	51
0	51
0	51
0	51
0	51
1	51
0	51
0	51
1	51
0	51
1	51
1	51
1	51
1	51
1	51
1	51
0	51
1	51
0	51
1	51
1	51
0	51
1	51
0	51
0	51
0	51
0	51
1	51
1	51
1	51
1	51
0	51
1	51
0	51
0	51
0	51
0	51
0	51
1	51
0	51
0	51
1	51
0	51
1	51
0	51
0	51
1	51
0	51
1	51
14) Clear the image memory.	52
15) Connect the line cable to the FAX box unit. Connect the line cable to the FAX box unit.	52
[11] MECHANICAL COUNTER INSTALLATION	53
[12] DRY HEATER INSTALLATION	54
1. Dry heater switch and dehumidifying heater relay PWB installation	54
2. Scanner dry heater installation	54
3. Dry heater (Paper feed trays 1, 2) installation	55