Sony DCR-IP220 Operating Instructions - Page 204

Maintenance information and precautions, Adjusting the LCD screen CALIBRATION, DISPLAY/TOUCH PANEL

Page 204 highlights

Maintenance information and precautions Adjusting the LCD screen (CALIBRATION) The buttons on the touch panel may not work correctly. If this happens, follow the procedure below. (1) Set the POWER switch to (CHG) OFF. (2) Eject the tape from your camcorder, then disconnect any connecting cable from your camcorder. (3) Close the LCD panel with the LCD screen facing out. DISPLAY/TOUCH PANEL (4) Set the POWER switch to VCR while pressing DISPLAY/TOUCH PANEL, then keep pressing DISPLAY/TOUCH PANEL for about five seconds. (5) Follow the procedure below with your finger or the supplied stylus (DCRIP220 only). 1 Touch at the upper left corner. 2 Touch at the lower right corner. 3 Touch in the middle of the LCD screen. CALIBRATE CALIBRATE CALIBRATE PB FN If you do not press the right spot, always returns to the position at the upper left corner. Note You can only carry out this operation with the LCD screen in the step 3 position. 204

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220

204
Maintenance information and precautions
Adjusting the LCD screen (CALIBRATION)
The buttons on the touch panel may not work correctly. If this happens, follow the
procedure below.
(
1
)
Set the POWER switch to (CHG) OFF.
(
2
)
Eject the tape from your camcorder, then disconnect any connecting cable from
your camcorder.
(
3
)
Close the LCD panel with the LCD screen facing out.
(
4
)
Set the POWER switch to VCR while pressing DISPLAY/TOUCH PANEL,
then keep pressing DISPLAY/TOUCH PANEL for about five seconds.
(
5
)
Follow the procedure below with your finger or the supplied stylus (DCR-
IP220 only).
1
Touch
at the upper left corner.
2
Touch
at the lower right corner.
3
Touch
in the middle of the LCD screen.
If you do not press the right spot,
always returns to the position at the upper
left corner.
Note
You can only carry out this operation with the LCD screen in the step 3 position.
CALIBRATE
CALIBRATE
CALIBRATE
PB
FN
DISPLAY/TOUCH PANEL