Home » TP-Link Manuals » Wireless » TP-Link TL-WA7210N » Manual Viewer

TP-Link TL-WA7210N User Guide - Page 18

Access Point, 3.4 Multi-SSID

Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

TL-WA7210N 2.4GHz 150Mbps Outdoor Wireless Access Point User Guide 2.3.3 Access Point This operation mode allows wireless stations to access. Figure 2-3 Hardware Installation of the TL-WA7210N in Access Point mode 1. Connect the LAN port of TL-WA7210N to the POE port of the Power Injector with an Ethernet cable. 2. Connect the LAN port of the Power Injector to the wired network port with an Ethernet cable. 3. Plug one end of the Power Adapter into the DC jack on the Power Injector, and the other end in the electrical wall socket. 4. Power on the notebook(s) and other connected devices (such as the Wired Router). 2.3.4 Multi-SSID In this mode, AP can support up to 4 SSID. Figure 2-4 Hardware Installation of the TL-WA7210N in Multi-SSID mode 1. Connect the LAN port of TL-WA7210N to the POE port of the Power Injector with an Ethernet cable. 2. Connect the LAN port of the Power Injector to the wired network port with an Ethernet cable. 3. Plug one end of the Power Adapter into the DC jack on the Power Injector, and the other end in the electrical wall socket. 4. Power on the notebooks and other connected devices (such as the Switch). 8

Section	Page
Package Contents	11
Chapter 1. Introduction	12
1.1 Overview of the Product	12
1.2 Features	12
1.3 Conventions	14
1.4 Panel Layout	14
1.4.1 The Front Panel	14
1.4.2 The Rear Panel	15
Chapter 2. Connecting the Device	16
2.1 System Requirements	16
2.2 Installation Environment Requirements	16
2.3 Connecting the Device	16
2.3.1 AP Client Router Mode	17
2.3.2 AP Router Mode	17
2.3.3 Access Point	18
2.3.4 Multi-SSID	18
2.3.5 Repeater and Universal Repeater	19
2.3.6 Bridge with AP	19
2.3.7 Client	20
Chapter 3. Quick Installation Guide	21
3.1 Configure the Device	21
3.2 Quick Setup	22
3.2.1 AP Client Router	25
3.2.2 AP Router	29
3.2.3 Access Point	33
3.2.4 Multi-SSID	36
3.2.5 Repeater (Range Extender)	38
3.2.6 Bridge with AP	42
3.2.7 Client	45
Chapter 4. AP & Multi-SSID & Repeater (Range Extender) & Bridge with AP & Client Operation Mode	50
4.1 Login	50
4.2 Status	50
4.3 Quick Setup	51
4.4 Operation Mode	51
4.5 WPS	52
4.6 Network	53
4.6.1 LAN	53
4.7 Wireless	54
4.7.1 Wireless Settings	55
4.7.2 Wireless Security	56
4.7.3 Wireless MAC Filtering	58
4.7.4 Wireless Advanced	61
4.7.5 Antenna Alignment	62
4.7.6 Distance Setting	62
4.7.7 Throughput Monitor	63
4.7.8 Wireless Statistics	63
4.8 DHCP	64
4.8.1 DHCP Settings	64
4.8.2 DHCP Clients List	65
4.8.3 Address Reservation	66
4.9 System Tools	67
4.9.1 SNMP	67
4.9.2 Time Settings	68
4.9.3 Diagnostic	70
4.9.4 Ping Watch Dog	71
4.9.5 Speed Test	71
4.9.6 Firmware Upgrade	72
4.9.7 Factory Defaults	73
4.9.8 Backup & Restore	73
4.9.9 Reboot	74
4.9.10 Password	74
4.9.11 System log	75
4.9.12 Statistics	76
Chapter 5. AP Client Router & AP Router Operation Mode	78
5.1 Login	78
5.2 Status	78
5.3 Quick Setup	80
5.4 Operation Mode	80
5.5 WPS	81
5.6 Network	82
5.6.1 WAN	82
5.6.2 MAC Clone	90
5.6.3 LAN	91
5.7 Wireless	91
5.7.1 Wireless Settings	92
5.7.2 Wireless Security	97
5.7.3 MAC Filtering	99
5.7.4 Wireless Advanced	101
5.7.5 Antenna Alignment	102
5.7.6 Distance Setting	102
5.7.7 Throughput Monitor	103
5.7.8 Wireless Statistics	103
5.8 DHCP	104
5.8.1 DHCP Settings	104
5.8.2 DHCP Clients List	105
5.8.3 Address Reservation	106
5.9 Forwarding	107
5.9.1 Virtual Servers	107
5.9.2 Port Triggering	109
5.9.3 DMZ	110
5.9.4 UPnP	111
5.10 Security	111
5.10.1 Basic Security	112
5.10.2 Advanced Security	113
5.10.3 Local Management	114
5.10.4 Remote Management	115
5.11 Parental Control	115
5.12 Access Control	117
5.12.1 Rule	117
5.12.2 Host	119
5.12.3 Target	120
5.12.4 Schedule	121
5.13 Advanced Routing	122
5.13.1 Static Routing List	122
5.13.2 System Routing Table	123
5.14 Bandwidth Control	124
5.14.1 Control Settings	124
5.14.2 Rules List	124
5.15 IP & MAC Binding	125
5.15.1 Binding Setting	125
5.15.2 ARP List	126
5.16 Dynamic DNS	127
5.17 System Tools	130
5.17.1 Time Settings	131
5.17.2 Diagnostic	132
5.17.3 Firmware Upgrade	133
5.17.4 Factory Defaults	134
5.17.5 Backup & Restore	134
5.17.6 Reboot	135
5.17.7 Password	135
5.17.8 System log	136
5.17.9 Statistics	138
Appendix A: FAQ	140
Appendix B: Configuring the PC	144
Appendix C: Specifications	148

Match case Limit results 1 per page

TL-WA7210N

2.4GHz 150Mbps Outdoor Wireless Access Point User Guide

2.3.3 Access Point

This operation mode allows wireless stations to access.

Figure 2-3 Hardware Installation of the TL-WA7210N in Access Point mode

Connect the LAN port of TL-WA7210N to the POE port of the Power Injector with an Ethernet

cable.

Connect the LAN port of the Power Injector to the wired network port with an Ethernet cable.

Plug one end of the Power Adapter into the DC jack on the Power Injector, and the other end

in the electrical wall socket.

Power on the notebook(s) and other connected devices (such as the Wired Router).

2.3.4 Multi-SSID

In this mode, AP can support up to 4 SSID.

Figure 2-4 Hardware Installation of the TL-WA7210N in Multi-SSID mode

Connect the LAN port of TL-WA7210N to the POE port of the Power Injector with an Ethernet

cable.

Connect the LAN port of the Power Injector to the wired network port with an Ethernet cable.

Plug one end of the Power Adapter into the DC jack on the Power Injector, and the other end

in the electrical wall socket.

Power on the notebooks and other connected devices (such as the Switch).