Yamaha M2500 Owner's Manual - Page 10
Aux 1, Aux 14, On/edit, Check, Signal - 32
View all Yamaha M2500 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 10 highlights
Control panel E EQ switch This turns the equalizer on/off. When the switch is pressed in ( ), the equalizer is on. F AUX 1-AUX 14 controls These adjust the level at which the signal of the stereo input channel (the L/R input signals mixed to a monaural signal) is sent to the AUX buses 1-14. Placing the control at the "v" position will produce nominal level (0 dB). For AUX buses 1/2, the pre-fader signal will be output. For AUX buses 3-14, the PRE switch (7) can be used to switch the signal pre or post fader. G PRE switches If these switches are turned on ( ), the pre-fader signal will be sent to the corresponding AUX buses. If these switches are turned off ( ), the post-fader signal will be sent. Switches are provided to independently switch three groups of AUX buses: 3-6, 7-10, and 11-14. H BAL control This adjusts the level balance of the signal that is sent to the STEREO or GROUP buses. q If the ST switch is on The BAL control will adjust the L/R balance at which the signal of the stereo input channel is sent to the STEREO bus. q If a 1-2/3-4/5-6/7-8 switch is on The BAL control will adjust the balance of the stereo input channel that is sent to the odd-numbered channels (1/3/5/7) and even-numbered channels (2/ 4/6/8) of the corresponding GROUP bus (1-2/3-4/56/7-8). The L ch of the input signal will be sent to the odd-numbered channel of the group bus, and the R channel of the input signal will be sent to the evennumbered channel of the group bus. I Channel assign switches These switches assign the signal that has passed through the fader and BAL control to the desired bus(es). Any or all of the channel assign switches can be used simultaneously. • 1-2/3-4/5-6/7-8 switches When these switches are on ( ), the signal of the stereo input channel will be sent to the corresponding GROUP bus (1-2/3-4/5-6/7-8). • ST (stereo) switch When this switch is on ( ), the signal of the stereo input channel will be sent to the STEREO bus. • MONO (monaural) switch When this switch is on ( ), the L and R channels of the input signal will be mixed to monaural, and sent to the MONO/C bus. The signal that is sent to the MONO/C bus is not affected by the BAL control. J ON/EDIT switch / ON, CHECK indicators The function of this switch and these indicators will change depending on the mode of the M2500. q In normal mode You can use the ON/EDIT switch to turn the stereo input channel on/off. When the channel is switched on/off, the ON indicator will be lit/dark to indicate the status. Channels that are switched off will not send any signals to the GROUP, STEREO. MONO/C, or AUX buses, but you can still use the PFL switch (M) to monitor the signal from the MONITOR OUT jacks or the PHONES jack. q In check mode When a scene is selected, the on/off status memorized in that scene will be indicated by the lit/dark status of the CHECK indicator. In check mode, you can also use the ON/EDIT switch to switch the CHECK indicator between lit/dark. For details on check mode, refer to page 32. K PEAK/NOM/SIGNAL indicators These three indicators allow you to check the prefader signal level of the stereo input channel. • PEAK indicator This will light when the signal mixed to monaural exceeds nominal level by 17 dB. • NOM (nominal) indicator This will light when the signal mixed to monaural reaches nominal level (0 dB). • SIGNAL indicator This will light when the signal mixed to monaural reaches a level 13 dB below nominal. L Channel fader This adjusts the output level of the stereo input channel signal. This fader affects the level of the signal that is sent to the GROUP, STEREO, MONO/C, and AUX (if the PRE switch is off) buses. M PFL (pre-fader listen) switch When this switch is on ( ), the pre-fader signal will be sent to the MONITOR INPUT PFL bus, and can be monitored from the MONITOR OUT and PHONES jacks. 7 M2500-Owner's Manual