Compaq AP500 Reference Guide - Page 76

Installing a Hard Drive in Bay 5 or 6, front bezel

Get Compaq AP500 - Professional - 128 MB RAM PDF manuals and user guides
UPC - 743172574732
View all Compaq AP500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 76 highlights

8-6 Drives Installing a Hard Drive in Bay 5 or 6 Drive bays 5 and 6 can be configured with either 1.0-inch or 1.6-inch hard drives. Other than using different screw holes, the installation for both drives is basically the same. To install a 1.6-inch hard drive: NOTE: Before installing a SCSI device, please read "SCSI Cables and Guidelines" later in this chapter. 1. Turn off the workstation and disconnect the power cord from the grounded AC outlet and the back of the workstation. 2. Remove the following components: t side access panel t front bezel t cooling shield 3. Refer to the following illustrations to install a 1.6-inch hard drive in bay 5 or 6. Figure 8-5. Installing a 1.6-inch hard drive in the hard drive bracket

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
8-6
Drives
Installing a Hard Drive in Bay 5 or 6
Drive bays 5 and 6 can be configured with either 1.0-inch or 1.6-inch hard
drives. Other than using different screw holes, the installation for both drives
is basically the same. To install a 1.6-inch hard drive:
NOTE
:
Before installing a SCSI device, please read
“SCSI Cables and
Guidelines” later in this chapter.
1.
Turn off the workstation and disconnect the power cord from the
grounded AC outlet and the back of the workstation.
2.
Remove the following components:
side access panel
front bezel
cooling shield
3.
Refer to the following illustrations to install a 1.6-inch hard drive in
bay 5 or 6.
Figure 8-5.
Installing a 1.6-inch hard drive in the hard drive bracket