HP Xw9400 HP xw9400 Workstation - Service and Technical Reference Guide - Page 75
Hood sensor (Smart cover sensor),
View all HP Xw9400 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 75 highlights
Hood sensor (Smart cover sensor) To remove the hood sensor: 1. Disconnect power from the system (Pre-disassembly procedures on page 55) and remove the access panel (Access panel on page 63). Remove the front bezel. Lay the workstation on its side with the system board facing up. 2. Remove the two hood sensor bracket screws, and remove the bracket and sensor as a unit. Figure 5-8 Removing the hood sensor To replace the hood sensor, reverse the previous steps. ENWW Removing and replacing components 65
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179
-
180
-
181
-
182
-
183
-
184
-
185
-
186
-
187
-
188
-
189
-
190
-
191
-
192
-
193
-
194
-
195
-
196
-
197
-
198
-
199
-
200
-
201
-
202
-
203
-
204
-
205
-
206
-
207
-
208
-
209
-
210
-
211
-
212
-
213
-
214
-
215
-
216
-
217
-
218
-
219
-
220
-
221
Hood sensor (Smart cover sensor)
To remove the hood sensor:
1.
Disconnect power from the system (
Pre-disassembly procedures
on page
55
) and remove the
access panel (
Access panel
on page
63
). Remove the front bezel. Lay the workstation on its side
with the system board facing up.
2.
Remove the two hood sensor bracket screws, and remove the bracket and sensor as a unit.
Figure 5-8
Removing the hood sensor
To replace the hood sensor, reverse the previous steps.
ENWW
Removing and replacing components
65