HP Xw9400 HP xw9400 Workstation - Service and Technical Reference Guide - Page 93

PCI or PCI Express installation,

Get HP Xw9400 - Workstation - 16 GB RAM PDF manuals and user guides View all HP Xw9400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 93 highlights

PCI or PCI Express installation 1. Disconnect power from the system (Pre-disassembly procedures on page 55), and remove the access panel (Access panel on page 63). Place the workstation on its side with the system board facing up, and remove the PCI retainer (PCI retention clamp on page 80). 2. Open the PCI retention clamp by pressing down on the two green clips (1) at the ends of the clamp and rotating the clamp toward the back of the system. 3. Remove the PCI slot cover (2). 4. Lower the PCI (3) or PCI Express (3) card into the chassis. Verify that the keyed components of the card align with the socket. If installing a card with an auxiliary power connector, plug in the power supply cable or adapter cable supplied with the card (4). 5. Ensure that all cards are properly seated, and close the PCI retention clamp. Figure 5-25 Installing PCI or PCIe card ENWW Removing and replacing components 83

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
PCI or PCI Express installation
1.
Disconnect power from the system (
Pre-disassembly procedures
on page
55
), and remove the
access panel (
Access panel
on page
63
). Place the workstation on its side with the system board
facing up, and remove the PCI retainer (
PCI retention clamp
on page
80
).
2.
Open the PCI retention clamp by pressing down on the two green clips
(1)
at the ends of the clamp
and rotating the clamp toward the back of the system.
3.
Remove the PCI slot cover
(2)
.
4.
Lower the PCI
(3)
or PCI Express
(3)
card into the chassis. Verify that the keyed components of
the card align with the socket.
If installing a card with an auxiliary power connector, plug in the power supply cable or adapter
cable supplied with the card
(4)
.
5.
Ensure that all cards are properly seated, and close the PCI retention clamp.
Figure 5-25
Installing PCI or PCIe card
ENWW
Removing and replacing components
83