Kodak 1252972 User Guide - Page 90

To see if you have an active network connection, No TCP/IP, Printer not found, On/Off, Probable Cause

Page 90 highlights

Troubleshooting To see if you have an active network connection Check the two Ethernet indicator lights on the top and bottom of the RJ-45 Ethernet jack on the back of the printer. The lights indicate the following: Top light If this light is a solid green, the device is properly connected to the network, and communications have been established. If the top light is off, there is no network connection. Bottom light This yellow light flashes when data is being sent or received by the device over the network. To establish an active network connection 1. Check the cable connections from the All-in-One printer to your gateway, router, or hub to ensure connections are secure. 2. If the connections are secure, turn off the power on the All-in-One printer, and then turn it on again. Press the On/Off button on the control panel to turn the printer off, and press it again to turn it back on. Also, turn off the power on your router or hub, and then turn it on again. No TCP/IP Probable Cause Your Local Area Network (LAN) card is not installed properly. Corrective Action Make sure your LAN card is installed properly and set up for TCP/IP. See the instructions that came with your LAN card. Printer not found Probable Cause The All-in-One printer is not turned on. Corrective Action Turn on the printer. Probable Cause 2 You do not have an active network connection. Corrective Action Make sure you have an active network connection. 82 www.kodak.com/go/aiosupport

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120

Troubleshooting
82
www.kodak.com/go/aiosupport
To see if you have an active network connection
Check the two Ethernet indicator lights on the top and bottom of the RJ-45 Ethernet
jack on the back of the printer. The lights indicate the following:
To establish an active network connection
1.
Check the cable connections from the All-in-One printer to your gateway,
router, or hub to ensure connections are secure.
2.
If the connections are secure, turn off the power on the All-in-One printer, and
then turn it on again. Press the
On/Off
button on the control panel to turn the
printer off, and press it again to turn it back on. Also, turn off the power on your
router or hub, and then turn it on again.
No TCP/IP
Probable Cause
Your Local Area Network (LAN) card is not installed properly.
Corrective Action
Make sure your LAN card is installed properly and set up for TCP/IP. See the
instructions that came with your LAN card.
Printer not found
Probable Cause
The All-in-One printer is not turned on.
Corrective Action
Turn on the printer.
Probable Cause 2
You do not have an active network connection.
Corrective Action
Make sure you have an active network connection.
Top light
If this light is a solid green, the device is properly
connected to the network, and communications have
been established. If the top light is off, there is no
network connection.
Bottom light
This yellow light flashes when data is being sent or
received by the device over the network.