Konica Minolta Kodak Ngenuity 9090DB User Guide - Page 25

Settings button, Resetting the maintenance reminders, Settings, Sleep timeout, Multifeed, Normal

Get Konica Minolta Kodak Ngenuity 9090DB PDF manuals and user guides View all Konica Minolta Kodak Ngenuity 9090DB manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

Settings button Resetting the maintenance reminders If a component's maintenance interval expires triggering the maintenance reminders, a hyperlink for that component will navigate you to reset and restart the interval count. This process is necessary to ensure required maintenance continues to be monitored appropriately. NOTE: The alerts for calibrating the front and back cameras cannot be adjusted. If an alert to calibrate the camera(s) is displayed, click the corresponding hyperlink to reset the reminder and begin calibration. For procedures on calibrating the cameras, see Chapter 5, Maintenance. When you click the Settings button on the Ngenuity Operator Utility main screen, the Configure Scanner Settings screen will be displayed. 3-12 You can configure basic scanner settings (e.g., Sleep timeout, Multifeed range, Custom Functions and Audio volume and sound) using this screen. Sleep timeout - you can set the delay time in hours and minutes that the scanner can be idle with full power before going into "sleep" mode. The default timeout is 15 minutes; the maximum time is 4 hours. Multifeed - allows you to adjust the sensitivity when scanning Normal or Very thin documents. • Normal: for documents that range from thick card stock to thin carbon copies. This setting should be used for most documents. • Very thin: used to detect multifeeds when scanning ultra-thin documents such as rice paper. A-61662 April 2010

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
3-12
A-61662
April 2010
Resetting the maintenance reminders
If a component’s maintenance interval expires triggering the
maintenance reminders, a hyperlink for that component will navigate
you to reset and restart the interval count. This process is necessary to
ensure required maintenance continues to be monitored appropriately.
NOTE: The alerts for calibrating the front and back cameras cannot be
adjusted. If an alert to calibrate the camera(s) is displayed, click
the corresponding hyperlink to reset the reminder and begin
calibration. For procedures on calibrating the cameras, see
Chapter 5, Maintenance.
Settings button
When you click the
Settings
button on the Ngenuity Operator Utility
main screen, the Configure Scanner Settings screen will be displayed.
You can configure basic scanner settings (e.g., Sleep timeout, Multifeed
range, Custom Functions and Audio volume and sound) using this
screen.
Sleep timeout
— you can set the delay time in hours and minutes that
the scanner can be idle with full power before going into “sleep” mode.
The default timeout is 15 minutes; the maximum time is 4 hours.
Multifeed
— allows you to adjust the sensitivity when scanning
Normal
or
Very thin
documents.
•
Normal
: for documents that range from thick card stock to thin
carbon copies. This setting should be used for most documents.
•
Very thin:
used to detect multifeeds when scanning ultra-thin
documents such as rice paper.