Konica Minolta Kodak Ngenuity 9090DB User Guide - Page 27

Maintenance button

Get Konica Minolta Kodak Ngenuity 9090DB PDF manuals and user guides View all Konica Minolta Kodak Ngenuity 9090DB manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

Maintenance button When you click the Maintenance button on the Ngenuity Operator Utility main screen, the Maintenance screen will be displayed. 3-14 This screen provides scanner statistics for total hours, total pages fed and total pages scanned. The Maintenance screen also allows you to configure reminders for different maintenance tasks that are required to ensure optimal performance. Scanner Stats - this area provides statistics for Total On Time (awake and sleeping), Total Pages (fed) and total Scanned Pages. These totals are updated every 2 seconds. Configuration Maintenance Reminders - allows you to set the interval values for triggering the reminders that are visible in the Maintenance section of the Home screen. Intervals can be set for cleaning the feed rollers (skimmer rollers: pick and drive and separator roller), the transport rollers, the optics and to replace the feed rollers (skimmer rollers and separator roller). These reminders can also be individually enabled and disabled. It is recommended that you do not disable any of these reminders. To enable and adjust a maintenance reminder, click the check box next to the corresponding component and use the up/down arrows in the Page Interval column to change the value. Click Save to save your changes or Restore to reset the values to the previously saved settings. The available interval settings and their defaults are: Reminder Range Default Clean Feed Rollers (skimmer rollers and separator roller) 1K - 50K 10K Clean Transport Rollers 5K - 100K 50K Clean Optics (camera covers, imaging guides, sensors) 5K - 150K 50K Replace Feed Rollers (skimmer rollers and separator roller) 100K - 900K 600K A-61662 April 2010

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
3-14
A-61662
April 2010
Maintenance button
When you click the
Maintenance
button on the Ngenuity Operator
Utility main screen, the Maintenance screen will be displayed.
This screen provides scanner statistics for total hours, total pages fed
and total pages scanned. The Maintenance screen also allows you to
configure reminders for different maintenance tasks that are required to
ensure optimal performance.
Scanner Stats
— this area provides statistics for
Total On Time
(awake and sleeping),
Total Pages
(fed) and total
Scanned Pages
.
These totals are updated every 2 seconds.
Configuration Maintenance Reminders
— allows you to set the
interval values for triggering the reminders that are visible in the
Maintenance section of the Home screen.
Intervals can be set for cleaning the feed rollers (skimmer rollers: pick
and drive and separator roller), the transport rollers, the optics and to
replace the feed rollers (skimmer rollers and separator roller). These
reminders can also be individually enabled and disabled. It is
recommended that you
do not
disable any of these reminders.
To enable and adjust a maintenance reminder, click the check box next
to the corresponding component and use the up/down arrows in the
Page Interval
column to change the value. Click
Save
to save your
changes or
Restore
to reset the values to the previously saved
settings.
The available interval settings and their defaults are:
Reminder
Range
Default
Clean Feed Rollers (skimmer rollers and separator roller)
1K - 50K
10K
Clean Transport Rollers
5K - 100K
50K
Clean Optics (camera covers, imaging guides, sensors)
5K - 150K
50K
Replace Feed Rollers (skimmer rollers and separator roller)
100K - 900K
600K