Home » Ricoh Manuals » Multifunction Devices » Ricoh Aficio MP 2000 » Manual Viewer

Ricoh Aficio MP 2000 Network Guide - Page 61

bonjour(rendezvous), IP TTL setting

View all Ricoh Aficio MP 2000 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

Remote Maintenance by telnet bonjour(rendezvous) Use the "bonjour(rendezvous)" command to display bonjour(rendezvous)-related settings. ❖ IP TTL setting msh> bonjour ip ttl {1-255} You can specify the IP TTL (the number of routers a packet can pass through). ❖ View settings Bonjour settings are displayed. Note ❒ The default is 255. 2 msh> bonjour ❖ Resetting the computer name and lo- ❖ Bonjour service name setting You can specify the bonjour service name. msh> bonjour cname "computer name" • The computer name can be entered using up to 63 alphanumeric characters. cation information You can reset the computer name and location information. msh> bonjour clear {cname | location} • cname Reset the computer name. The default computer name will be displayed when the computer is ❖ Bonjour Installation location information setting You can enter information about the location where the printer is installed. restarted. • location Reset the location information. The previous location information will be deleted. msh> bonjour location "location" • Information about location can be entered using up to 32 alphanumeric characters. ❖ Setting order of priority for each protocol • diprint msh> bonjour diprint [0- 99] • lpr msh> bonjour lpr [0-99] ❖ Interface configuration msh> bonjour linklocal "interface_name" • If many types of interface are installed, configure the interface that communicates with linklocal address. • If you do not specify an interface, the Ethernet interface is automatically selected. • wlan can be specified only when the IEEE 802.11b interface is installed. • ipp Interface Interface configured msh> bonjour ipp [0-99] ether You can specify the order of priority for "diprint", "lpr", and "ipp". wlan Smaller numbers indicate higher priority. Ethernet interface IEEE 802.11b interface 53

Section	Page
Network Guide	1
Introduction	2
Important	2
Notes	2
Software Version Conventions Used in This Manual	2
Manuals for This Machine	3
TABLE OF CONTENTS	5
How to Read This Manual	9
Symbols	9
Setting Up the Machine on a Network	10
Initial Settings Overview	10
Initial Settings	12
1. Using a Printer Server	23
Preparing Printer Server	23
Printing notification via SmartDeviceMonitor for Client	23
Setting the print server	23
Setting a Client	24
Using NetWare	25
Setting Up as a Print Server (NetWare 3.x)	25
Setting Up as a Print Server (NetWare 4.x, 5 / 5.1, 6 / 6.5)	27
Using Pure IP in the NetWare 5 / 5.1 or 6 / 6.5 Environment	28
Setting Up as a Remote Printer (NetWare 3.x)	29
Setting Up as a Remote Printer (NetWare 4.x, 5 / 5.1, 6 / 6.5)	31
2. Monitoring and Configuring the Printer	35
Using Web Image Monitor	35
Displaying Top Page	37
When user authentication is set	38
Login (using Web Image Monitor)	38
Log Off (using Web Image Monitor)	38
About Menu and Mode	39
Access in the Administrator Mode	41
Displaying Web Image Monitor Help	41
Downloading Help	41
Linking the URL of the Help File to the [Help] Button.	41
Using SmartDeviceMonitor for Admin	42
Installing SmartDeviceMonitor for Admin	43
Changing the Network Interface Board Configuration	43
Locking the Menus on the Machine's Control Panel	44
Changing the Paper Type	45
Managing User Information	45
Starting User Management Tool	45
Displaying the Number of Sheets Printed	46
Exporting the information about the number of pages printed	46
Resetting the number of pages printed to 0.	46
Restricting Functions	47
Setting Applicable Functions to New Users	47
Configuring the Energy Saver Mode	47
Setting a Password	48
Checking the Machine Status	48
Changing Names and Comments	49
Load Fax Journal	50
Managing Address Information	50
Using SmartDeviceMonitor for Client	51
Monitoring Printers	51
Checking the Machine Status	51
When Using IPP with SmartDeviceMonitor for Client	52
Printer Status Notification by E-Mail	53
Auto E-mail Notification	54
On-demand E-mail Notification	55
Mail authentication	55
On-demand E-mail Notification	56
Remote Maintenance by telnet	58
Using telnet	58
access	58
appletalk	59
authfree	60
autonet	60
bonjour(rendezvous)	61
btconfig	62
devicename	62
dhcp	62
diprint	63
dns	64
domainname	65
help	65
hostname	66
ifconfig	66
info	67
ipp	67
ipv6	68
lpr	68
netware	68
passwd	69
prnlog	69
route	69
set	71
show	72
slp	72
smb	72
snmp	73
sntp	75
ssdp	76
ssh	76
status	76
syslog	76
upnp	77
web	77
wiconfig	77
wins	81
SNMP	82
Getting Printer Information over the Network	83
Current Printer Status	83
Printer configuration	88
Understanding the Displayed Information	89
Print Job Information	89
Print Log Information	90
Configuring the Network Interface Board	91
Message List	98
System Log Information	98
3. Special Operations under Windows	105
Printing Files Directly from Windows	105
Setup	105
Using a Host Name Instead of an IPv4 Address	105
When using DNS	105
When setting the IPv4 address of a printer using DHCP	105
In other cases	106
Printing Commands	107
lpr	107
rcp	107
ftp/sftp	108
4. Appendix	109
When Using Windows Terminal Service / MetaFrame	109
Operating Environment	109
Supported Printer Drivers	109
Limitations	109
Using DHCP	111
Using AutoNet	111
Precautions	112
Connecting a Dial-Up Router to a Network	112
When using NetWare (file server)	112
When Using Network Utility	113
NetWare Printing	113
Form feed	113
Banner page	114
Printing after resetting the machine	114
When the optional IEEE 802.11b interface unit Is Installed	114
Information about Installed Applications	115
RSA® BSAFE	115
Specifications	116

Match case Limit results 1 per page

Remote Maintenance by telnet

bonjour(rendezvous)

Use the “bonjour(rendezvous)” com-

mand to display bonjour(rendez-

vous)-related settings.

❖

View settings

Bonjour settings are displayed.

msh> bonjour

❖

Bonjour service name setting

You can specify the bonjour serv-

ice name.

msh> bonjour cname “compu-

ter name”

•

The computer name can be en-

tered using up to 63 alphanu-

meric characters.

❖

Bonjour Installation location informa-

tion setting

You can enter information about

the location where the printer is in-

stalled.

msh> bonjour location “lo-

cation”

•

Information about location can

be entered using up to 32 alpha-

numeric characters.

❖

Setting order of priority for each pro-

tocol

• diprint

msh> bonjour diprint [0–

99]

• lpr

msh> bonjour lpr [0–99]

• ipp

msh> bonjour ipp [0–99]

You can specify the order of prior-

ity for “diprint”, “lpr”, and “ipp”.

Smaller numbers indicate higher

priority.

❖

IP TTL setting

msh> bonjour ip ttl {1-255}

You can specify the IP TTL (the

number of routers a packet can

pass through).

Note

❒

The default is 255.

❖

Resetting the computer name and lo-

cation information

You can reset the computer name

and location information.

msh> bonjour clear {cname

| location}

• cname

Reset the computer name. The

default computer name will be

displayed when the computer is

restarted.

• location

Reset the location information.

The previous location informa-

tion will be deleted.

❖

Interface configuration

msh> bonjour linklocal

“interface_name”

•

If many types of interface are in-

stalled, configure the interface

that communicates with linklo-

cal address.

•

If you do not specify an inter-

face, the Ethernet interface is

automatically selected.

• wlan can be specified only

when the IEEE 802.11b interface

is installed.

Interface

Interface configured

ether

Ethernet interface

wlan

IEEE 802.11b inter-

face