Ricoh Aficio MP 2000 Network Guide - Page 81

wins, msh> wins, msh> wins interface_name, on | off}, primary|secondary} IP, address

Get Ricoh Aficio MP 2000 PDF manuals and user guides View all Ricoh Aficio MP 2000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 81 highlights

Remote Maintenance by telnet wins Use the "wins" command to configure WINS server settings. ❖ NBT (NetBIOS over TCP/IP) Scope ID Selection You can specify the NBT scope ID. msh> wins "interface_name" scope "scope ID" ❖ Viewing settings msh> wins • If the IPv4 address obtained from DHCP differs from the WINS IPv4 address, the DHCP address is the valid address. ❖ Configuration msh> wins "interface_name" {on | off} • The scope ID can be entered us- ing up to 31 alphanumeric char- acters. 2 • Be sure to specify the interface. • wlan can be specified only when the IEEE 802.11b interface is installed. Interface name ether Interface configured Ethernet interface • {on} means "active" and {off} wlan means "inactive". IEEE 802.11b interface • Be sure to specify the interface. • wlan can be specified only when the IEEE 802.11b interface is installed. Interface name Interface configured ether Ethernet interface wlan IEEE 802.11b interface ❖ Address configuration Use the following command to configure a WINS server IP address: msh> wins "interface_name" {primary|secondary} "IP address" • Use the "primary" command to configure a primary WINS server IP address. • Use the "secondary" command to configure a secondary WINS server IP address. • Do not use "255.255.255.255" as the IP address. 73

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
Remote Maintenance by telnet
73
2
wins
Use the "wins" command to configure
WINS server settings.
❖
Viewing settings
msh> wins
• If the IPv4 address obtained
from DHCP differs from the
WINS IPv4 address, the DHCP
address is the valid address.
❖
Configuration
msh> wins “interface_name”
{on | off}
• {on} means "active" and {off}
means "inactive".
•
Be sure to specify the interface.
• wlan can be specified only
when the IEEE 802.11b interface
is installed.
❖
Address configuration
Use the following command to
configure a WINS server IP ad-
dress:
msh> wins “interface_name”
{primary|secondary} “IP
address”
•
Use the “primary” command to
configure a primary WINS serv-
er IP address.
•
Use the "secondary" command
to configure a secondary WINS
server IP address.
•
Do not use “255.255.255.255” as
the IP address.
❖
NBT (NetBIOS over TCP/IP) Scope ID
Selection
You can specify the NBT scope ID.
msh> wins “interface_name”
scope “scope ID”
•
The scope ID can be entered us-
ing up to 31 alphanumeric char-
acters.
•
Be sure to specify the interface.
• wlan can be specified only
when the IEEE 802.11b interface
is installed.
Interface name
Interface configured
ether
Ethernet interface
wlan
IEEE 802.11b inter-
face
Interface name
Interface configured
ether
Ethernet interface
wlan
IEEE 802.11b inter-
face