Home » Ricoh Manuals » Multifunction Devices » Ricoh Aficio MP 2000 » Manual Viewer

Ricoh Aficio MP 2000 Network Guide - Page 74

Remote Configuration Authorization, SNMP TRAP configuration

View all Ricoh Aficio MP 2000 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 74 highlights

Monitoring and Configuring the Printer ❖ Protocol configuration • To specify IPv4 or IPv6, enter msh> snmp {ipv4|ipv6|ipx} "ipv4" or "ipv6" followed by a {on|off} space, and then the IPv4 or IPv6 address. • Use the following command to set protocols "active" or "inactive": If you set a protocol "inac- • To specify IPX/SPX, enter "ipx" followed by a space, the IPX ad- 2 tive", all access settings for that protocol are disabled. dress followed by a decimal, and then the MAC address of the network interface board. • Specify "ipv4" for IPv4, "ipv6" for IPv6, or "ipx" for IPX/SPX. ❖ sysLocation configuration • {on} means "active" and {off} means "inactive". • All protocols cannot be turned off concurrently. msh> snmp location ❖ Deleting sysLocation msh> snmp clear location ❖ Configuration of protocol for each registration number msh> snmp "number" active {ipv4|ipv6|ipx} {on|off} • To change the protocol of access settings, use the following command. However, if you have disabled a protocol with the above command, activating it here has no effect. ❖ Access configuration msh> snmp "number" {ipv4|ipv6|ipx} "address" • You can configure a host address according to the protocol used. • The network interface board accepts requests only from hosts that have IPv4, IPv6, and IPX addresses with access types of "read-only" or "read-write". Enter "0" to have network interface board accept requests from any host without requiring a specific type of access. • Enter a host address to deliver "trap" access type information to. ❖ sysContact setting msh> snmp contact ❖ Deleting sysContact msh> snmp clear contact ❖ SNMP v1v2 function configuration msh> snmp v1v2 {on|off} • Specify "on" to enable, and "off" to disable. ❖ SNMP v3 function configuration msh> snmp v3 {on|off} • Specify "on" to enable, and "off" to disable. ❖ SNMP TRAP configuration msh> snmp trap {v1|v2|v3} {on|off} • Specify "on" to enable, and "off" to disable. ❖ Remote Configuration Authorization configuration msh> snmp remote {on|off} • Specify "on" to enable, and "off" to disable the SNMP v1v2 setting. 66

Section	Page
Network Guide	1
Introduction	2
Important	2
Notes	2
Software Version Conventions Used in This Manual	2
Manuals for This Machine	3
TABLE OF CONTENTS	5
How to Read This Manual	9
Symbols	9
Setting Up the Machine on a Network	10
Initial Settings Overview	10
Initial Settings	12
1. Using a Printer Server	23
Preparing Printer Server	23
Printing notification via SmartDeviceMonitor for Client	23
Setting the print server	23
Setting a Client	24
Using NetWare	25
Setting Up as a Print Server (NetWare 3.x)	25
Setting Up as a Print Server (NetWare 4.x, 5 / 5.1, 6 / 6.5)	27
Using Pure IP in the NetWare 5 / 5.1 or 6 / 6.5 Environment	28
Setting Up as a Remote Printer (NetWare 3.x)	29
Setting Up as a Remote Printer (NetWare 4.x, 5 / 5.1, 6 / 6.5)	31
2. Monitoring and Configuring the Printer	35
Using Web Image Monitor	35
Displaying Top Page	37
When user authentication is set	38
Login (using Web Image Monitor)	38
Log Off (using Web Image Monitor)	38
About Menu and Mode	39
Access in the Administrator Mode	41
Displaying Web Image Monitor Help	41
Downloading Help	41
Linking the URL of the Help File to the [Help] Button.	41
Using SmartDeviceMonitor for Admin	42
Installing SmartDeviceMonitor for Admin	43
Changing the Network Interface Board Configuration	43
Locking the Menus on the Machine's Control Panel	44
Changing the Paper Type	45
Managing User Information	45
Starting User Management Tool	45
Displaying the Number of Sheets Printed	46
Exporting the information about the number of pages printed	46
Resetting the number of pages printed to 0.	46
Restricting Functions	47
Setting Applicable Functions to New Users	47
Configuring the Energy Saver Mode	47
Setting a Password	48
Checking the Machine Status	48
Changing Names and Comments	49
Load Fax Journal	50
Managing Address Information	50
Using SmartDeviceMonitor for Client	51
Monitoring Printers	51
Checking the Machine Status	51
When Using IPP with SmartDeviceMonitor for Client	52
Printer Status Notification by E-Mail	53
Auto E-mail Notification	54
On-demand E-mail Notification	55
Mail authentication	55
On-demand E-mail Notification	56
Remote Maintenance by telnet	58
Using telnet	58
access	58
appletalk	59
authfree	60
autonet	60
bonjour(rendezvous)	61
btconfig	62
devicename	62
dhcp	62
diprint	63
dns	64
domainname	65
help	65
hostname	66
ifconfig	66
info	67
ipp	67
ipv6	68
lpr	68
netware	68
passwd	69
prnlog	69
route	69
set	71
show	72
slp	72
smb	72
snmp	73
sntp	75
ssdp	76
ssh	76
status	76
syslog	76
upnp	77
web	77
wiconfig	77
wins	81
SNMP	82
Getting Printer Information over the Network	83
Current Printer Status	83
Printer configuration	88
Understanding the Displayed Information	89
Print Job Information	89
Print Log Information	90
Configuring the Network Interface Board	91
Message List	98
System Log Information	98
3. Special Operations under Windows	105
Printing Files Directly from Windows	105
Setup	105
Using a Host Name Instead of an IPv4 Address	105
When using DNS	105
When setting the IPv4 address of a printer using DHCP	105
In other cases	106
Printing Commands	107
lpr	107
rcp	107
ftp/sftp	108
4. Appendix	109
When Using Windows Terminal Service / MetaFrame	109
Operating Environment	109
Supported Printer Drivers	109
Limitations	109
Using DHCP	111
Using AutoNet	111
Precautions	112
Connecting a Dial-Up Router to a Network	112
When using NetWare (file server)	112
When Using Network Utility	113
NetWare Printing	113
Form feed	113
Banner page	114
Printing after resetting the machine	114
When the optional IEEE 802.11b interface unit Is Installed	114
Information about Installed Applications	115
RSA® BSAFE	115
Specifications	116

Match case Limit results 1 per page

Monitoring and Configuring the Printer

❖

Protocol configuration

msh> snmp {ipv4|ipv6|ipx}

{on|off}

•

Use the following command to

set protocols "active" or "inac-

tive": If you set a protocol "inac-

tive", all access settings for that

protocol are disabled.

• Specify "ipv4" for IPv4, "ipv6"

for IPv6, or "ipx" for IPX/SPX.

• {on} means "active" and {off}

means "inactive".

•

All protocols cannot be turned

off concurrently.

❖

Configuration of protocol for each

registration number

msh> snmp “number” active

{ipv4|ipv6|ipx} {on|off}

•

To change the protocol of access

settings, use the following com-

mand. However, if you have

disabled a protocol with the

above command, activating it

here has no effect.

❖

Access configuration

msh> snmp “number”

{ipv4|ipv6|ipx} “address”

• You can configure a host ad-

dress according to the protocol

used.

•

The network interface board ac-

cepts requests only from hosts

that have IPv4, IPv6, and IPX

addresses with access types of

"read-only" or "read-write". En-

ter “0” to have network inter-

face board accept requests from

any host without requiring a

specific type of access.

•

Enter a host address to deliver

"trap" access type information

to.

• To specify IPv4 or IPv6, enter

"ipv4" or "ipv6" followed by a

space, and then the IPv4 or IPv6

address.

•

To specify IPX/SPX, enter "ipx"

followed by a space, the IPX ad-

dress followed by a decimal,

and then the MAC address of

the network interface board.

❖

sysLocation configuration

msh> snmp location

❖

Deleting sysLocation

msh> snmp clear location

❖

sysContact setting

msh> snmp contact

❖

Deleting sysContact

msh> snmp clear contact

❖

SNMP v1v2 function configuration

msh> snmp v1v2 {on|off}

•

Specify "on" to enable, and "off"

to disable.

❖

SNMP v3 function configuration

msh> snmp v3 {on|off}

•

Specify "on" to enable, and "off"

to disable.

❖

SNMP TRAP configuration

msh> snmp trap {v1|v2|v3}

{on|off}

•

Specify "on" to enable, and "off"

to disable.

❖

Remote Configuration Authorization

configuration

msh> snmp remote {on|off}

•

Specify "on" to enable, and "off"

to disable the SNMP v1v2 set-

ting.