Home » Ricoh Manuals » Multifunction Devices » Ricoh Aficio MP 2000 » Manual Viewer

Ricoh Aficio MP 2000 Network Guide - Page 75

sntp, View settings

View all Ricoh Aficio MP 2000 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 75 highlights

Remote Maintenance by telnet ❖ SNMP v3 TRAP configuration display msh> snmp v3trap sntp msh> snmp v3trap {1-5} The printer clock can be synchronized • If a number from 1-5 is entered, with a NTP server clock using Simple settings are displayed for that Network Time Protocol (SNTP). Use number only. the "sntp" command to change SNTP settings. ❖ Configuring a sending address for 2 SNMP v3 TRAP ❖ View settings msh> snmp v3trap {1-5} msh> sntp {ipv4|ipv6|ipx} "address" ❖ Configuring a sending protocol for SNMP v3 TRAP ❖ NTP server address configuration You can specify the IP address of the NTP server. msh> snmp v3trap {1-5} ac- msh> sntp server "IP_address" tive {ipv4|ipv6|ipx} {on|off} ❖ Configuring a user account for SNMP v3 TRAP msh> snmp v3trap {1-5} account "account_name" • Enter an account name using up to 32 alphanumeric characters. ❖ Deleting an SNMP v3 TRAP user account ❖ Interval configuration msh> sntp interval "polling_time" • You can specify the interval at which the printer synchronizes with the operator-specified NTP server. The default is 60 minutes. • The interval can be entered from 0, or between 16 and 10,080 minutes. msh> snmp v3trap {1-5} clear account ❖ Configuring an SNMP v3 encryption algorithm msh> snmp v3auth {md5|sha1} • If you set 0, the printer synchronizes with the NTP server only when you turn the printer on. After that, the printer does not synchronize with the NTP server. ❖ Configuring SNMP v3 encryption msh> snmp v3priv {auto|on} • Set "auto" for automatic encryption configuration • Set "on" for mandatory encryption configuration. ❖ Time-zone configuration msh> sntp timezone "+/hour_time" • You can specify the time difference between the printer clock and NTP server clock. The values are between -12:00 and +13:00. 67

Section	Page
Network Guide	1
Introduction	2
Important	2
Notes	2
Software Version Conventions Used in This Manual	2
Manuals for This Machine	3
TABLE OF CONTENTS	5
How to Read This Manual	9
Symbols	9
Setting Up the Machine on a Network	10
Initial Settings Overview	10
Initial Settings	12
1. Using a Printer Server	23
Preparing Printer Server	23
Printing notification via SmartDeviceMonitor for Client	23
Setting the print server	23
Setting a Client	24
Using NetWare	25
Setting Up as a Print Server (NetWare 3.x)	25
Setting Up as a Print Server (NetWare 4.x, 5 / 5.1, 6 / 6.5)	27
Using Pure IP in the NetWare 5 / 5.1 or 6 / 6.5 Environment	28
Setting Up as a Remote Printer (NetWare 3.x)	29
Setting Up as a Remote Printer (NetWare 4.x, 5 / 5.1, 6 / 6.5)	31
2. Monitoring and Configuring the Printer	35
Using Web Image Monitor	35
Displaying Top Page	37
When user authentication is set	38
Login (using Web Image Monitor)	38
Log Off (using Web Image Monitor)	38
About Menu and Mode	39
Access in the Administrator Mode	41
Displaying Web Image Monitor Help	41
Downloading Help	41
Linking the URL of the Help File to the [Help] Button.	41
Using SmartDeviceMonitor for Admin	42
Installing SmartDeviceMonitor for Admin	43
Changing the Network Interface Board Configuration	43
Locking the Menus on the Machine's Control Panel	44
Changing the Paper Type	45
Managing User Information	45
Starting User Management Tool	45
Displaying the Number of Sheets Printed	46
Exporting the information about the number of pages printed	46
Resetting the number of pages printed to 0.	46
Restricting Functions	47
Setting Applicable Functions to New Users	47
Configuring the Energy Saver Mode	47
Setting a Password	48
Checking the Machine Status	48
Changing Names and Comments	49
Load Fax Journal	50
Managing Address Information	50
Using SmartDeviceMonitor for Client	51
Monitoring Printers	51
Checking the Machine Status	51
When Using IPP with SmartDeviceMonitor for Client	52
Printer Status Notification by E-Mail	53
Auto E-mail Notification	54
On-demand E-mail Notification	55
Mail authentication	55
On-demand E-mail Notification	56
Remote Maintenance by telnet	58
Using telnet	58
access	58
appletalk	59
authfree	60
autonet	60
bonjour(rendezvous)	61
btconfig	62
devicename	62
dhcp	62
diprint	63
dns	64
domainname	65
help	65
hostname	66
ifconfig	66
info	67
ipp	67
ipv6	68
lpr	68
netware	68
passwd	69
prnlog	69
route	69
set	71
show	72
slp	72
smb	72
snmp	73
sntp	75
ssdp	76
ssh	76
status	76
syslog	76
upnp	77
web	77
wiconfig	77
wins	81
SNMP	82
Getting Printer Information over the Network	83
Current Printer Status	83
Printer configuration	88
Understanding the Displayed Information	89
Print Job Information	89
Print Log Information	90
Configuring the Network Interface Board	91
Message List	98
System Log Information	98
3. Special Operations under Windows	105
Printing Files Directly from Windows	105
Setup	105
Using a Host Name Instead of an IPv4 Address	105
When using DNS	105
When setting the IPv4 address of a printer using DHCP	105
In other cases	106
Printing Commands	107
lpr	107
rcp	107
ftp/sftp	108
4. Appendix	109
When Using Windows Terminal Service / MetaFrame	109
Operating Environment	109
Supported Printer Drivers	109
Limitations	109
Using DHCP	111
Using AutoNet	111
Precautions	112
Connecting a Dial-Up Router to a Network	112
When using NetWare (file server)	112
When Using Network Utility	113
NetWare Printing	113
Form feed	113
Banner page	114
Printing after resetting the machine	114
When the optional IEEE 802.11b interface unit Is Installed	114
Information about Installed Applications	115
RSA® BSAFE	115
Specifications	116

Match case Limit results 1 per page

Remote Maintenance by telnet

❖

SNMP v3 TRAP configuration display

msh> snmp v3trap

msh> snmp v3trap {1-5}

•

If a number from 1-5 is entered,

settings are displayed for that

number only.

❖

Configuring a sending address for

SNMP v3 TRAP

msh> snmp v3trap {1-5}

{ipv4|ipv6|ipx} “address”

❖

Configuring a sending protocol for

SNMP v3 TRAP

msh> snmp v3trap {1-5} ac-

tive {ipv4|ipv6|ipx}

{on|off}

❖

Configuring a user account for SNMP

v3 TRAP

msh> snmp v3trap {1-5} ac-

count “account_name”

•

Enter an account name using up

to 32 alphanumeric characters.

❖

Deleting an SNMP v3 TRAP user ac-

count

msh> snmp v3trap {1-5}

clear account

❖

Configuring an SNMP v3 encryption

algorithm

msh> snmp v3auth {md5|sha1}

❖

Configuring SNMP v3 encryption

msh> snmp v3priv {auto|on}

•

Set "auto" for automatic encryp-

tion configuration

•

Set "on" for mandatory encryp-

tion configuration.

sntp

The printer clock can be synchronized

with a NTP server clock using Simple

Network Time Protocol (SNTP). Use

the "sntp" command to change SNTP

settings.

❖

View settings

msh> sntp

❖

NTP server address configuration

You can specify the IP address of

the NTP server.

msh> sntp server “IP_address”

❖

Interval configuration

msh> sntp interval

“polling_time”

•

You can specify the interval at

which the printer synchronizes

with the operator-specified

NTP server. The default is 60

minutes.

• The interval can be entered

from 0, or between 16 and

10,080 minutes.

•

If you set 0, the printer synchro-

nizes with the NTP server only

when you turn the printer on.

After that, the printer does not

synchronize with the NTP serv-

er.

❖

Time-zone configuration

msh> sntp timezone “+/-

hour_time”

•

You can specify the time differ-

ence between the printer clock

and NTP server clock. The val-

ues are between –12:00 and

+13:00.