Sharp DC500 FO-DC500 FO-DC525 FO-DC600 Operation Manual - Page 80

Initializing the network interface board

Page 80 highlights

Setting the IP Address 11 Wait while the machine writes the setting to the NIC board ("DO NOT POWER DOWN" will appear in the display). When the display changes to "OK", turn off the power of the machine and then turn it back on to make the new settings take effect. (Before turning off the power, make sure the machine is not in the middle of a job: 1) check whether the machine is printing, and 2) press JOB STATUS and check the display to see if the machine is sending or receiving a fax.) Initializing the network interface board Normally the network interface board (NIC) does not need to be initialized (returned to the factory default settings). In the event that you do need to initialize the board, follow the Steps 1 to 3 of the previous procedure to access "NETWORK CONFIG SET", press to select "INTIALIZE THE NIC", and then press START/ ENTER . Press to select "YES" and then press START/ ENTER . Wait while the machine writes the setting to the NIC board ("DO NOT POWER DOWN" will appear in the display). When the display changes to "OK", turn off the power of the machine and then turn it back on to make the new setting take effect. (Before turning off the power, make sure the machine is not in the middle of a job: 1) check whether the machine is printing, and 2) press JOB STATUS and check the display to see if the machine is sending or receiving a fax.) 78

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248

Setting the IP Address
78
11
Wait while the machine writes the setting to the NIC board (“DO NOT
POWER DOWN” will appear in the display). When the display changes to
“OK”, turn off the power of the machine and then turn it back on to make
the new settings take effect. (Before turning off the power, make sure
the machine is not in the middle of a job: 1) check whether the machine
is printing, and 2) press
and check the display to see if the
machine is sending or receiving a fax
.)
JOB STATUS
Initializing the network interface board
Normally the network interface board (NIC) does not need to be initialized
(returned to the factory default settings). In the event that you do need to
initialize the board, follow the Steps 1 to 3 of the previous procedure to access
“NETWORK CONFIG SET”, press
to select “INTIALIZE THE NIC”, and
then press
. Press
to select “YES” and then press
. Wait
while the machine writes the setting to the NIC board (“DO NOT POWER
DOWN” will appear in the display). When the display changes to “OK”, turn off
the power of the machine and then turn it back on to make the new setting
take effect. (Before turning off the power, make sure the machine is not in the
middle of a job: 1) check whether the machine is printing, and 2) press
and check the display to see if the machine is sending or receiving a
fax
.)
START/
ENTER
START/
ENTER
JOB STATUS