Dell PowerConnect 8100 Release Notes - Page 28

Dell Easy Setup

Get Dell PowerConnect 8100 PDF manuals and user guides View all Dell PowerConnect 8100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

1. Changes are not applied to the correct interfaces on the pages "System>sFlow>Sampler Configuration" "System>sFlow->Poll Configuration" 1. Changes were not applied to the correct interfaces on the GUI pages referred to. 2. An incorrect error message was displayed. 1. Used initialized buffers. 2. Correct the error message. All 4.2 supported platforms 2. Incorrect error message is displayed when not configured Receiver index is applied to interface on "System>sFlow->Poll Configuration" page. "show ip route configured ...longerprefixes" reports that default gateway is not configured, which is incorrect. CLI command "show ip route 192.168.2.2 /24" not ignoring host bits. CLI command "show spanningtree detail" missing information. "ipv6 pim joinprune interval" command does not work Macro input string does not accept more than 20 characters startup-config failed error message is displayed when finishing the Dell Easy Setup Wizard The default gateway would not be shown on executing "show ip route configured" The user would not always get the correct list of routes from the "show ip route" command. The user could not see the configured values for spanning tree max hops. The user could not change the configuration of the IPv6 PIM join interval. The interface string length is limited to 20 characters for the "macro global apply" command. startup-config failed error message is displayed when finishing the Dell Easy Setup Wizard Corrected the implementation of this command so that it functions correctly. Corrected the logic in the implementation of the "show ip routes" command so that the appropriate list of routes are shown, depending upon which optional parameters are given. Changed the output of the "show spanning-tree" and "show spanning-tree detail" commands to include the configured value of max hops. Corrected the implementation of this command so that it functions correctly. Increased the acceptable string length for the "macro global apply" command to 256 characters. Corrected the implementation of this command so that it functions correctly. All 4.2 supported platforms All 4.2 supported platforms All 4.2 supported platforms All 4.2 supported platforms All 4.2 supported platforms All 4.2 supported platforms 26 System Firmware Version 5.1.0.1

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
26
System Firmware Version 5.1.0.1
1. Changes are
not applied to
the correct
interfaces on the
pages
"System-
>sFlow-
>Sampler
Configuration"
"System-
>sFlow->Poll
Configuration"
2. Incorrect
error message is
displayed when
not configured
Receiver index
is applied
to interface on
"System-
>sFlow->Poll
Configuration"
page.
1. Changes were not applied to the correct
interfaces on the GUI pages referred to.
2. An incorrect error message was
displayed.
1. Used initialized buffers.
2. Correct the error message.
All 4.2 supported
platforms
"show ip route
configured
...longer-
prefixes" reports
that default
gateway is not
configured,
which is
incorrect.
The default gateway would not be shown on
executing "show ip route configured"
Corrected the implementation
of this command so that it
functions correctly.
All 4.2 supported
platforms
CLI command
"show ip route
192.168.2.2 /24"
not ignoring
host bits.
The user would not always get the correct
list of routes from the "show ip route"
command.
Corrected the logic in the
implementation of the "show
ip routes" command so that the
appropriate list of routes are
shown, depending upon which
optional parameters are given.
All 4.2 supported
platforms
CLI command
"show spanning-
tree detail"
missing
information.
The user could not see the configured
values for spanning tree max hops.
Changed the output of the
"show spanning-tree" and
"show spanning-tree detail"
commands to include the
configured value of max hops.
All 4.2 supported
platforms
"ipv6 pim join-
prune interval"
command does
not work
The user could not change the configuration
of the IPv6 PIM join interval.
Corrected the implementation
of this command so that it
functions correctly.
All 4.2 supported
platforms
Macro input
string does not
accept more
than 20
characters
The interface string length is limited to 20
characters for the "macro global apply"
command.
Increased the acceptable string
length for the "macro global
apply" command to 256
characters.
All 4.2 supported
platforms
startup-config
failed error
message is
displayed when
finishing the
Dell Easy Setup
Wizard
startup-config failed error message is
displayed when finishing the Dell Easy
Setup Wizard
Corrected the implementation
of this command so that it
functions correctly.
All 4.2 supported
platforms