HP 750c HP DesignJet 700 user guide - Page 192

The messages are listed in alphabetical order. - reseat cartridge error

Get HP 750c - DesignJet Plus Color Inkjet Printer PDF manuals and user guides View all HP 750c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 192 highlights

Front-Panel Messages Front-Panel Messages This is a list of all possible messages in the front-panel display. If you need to do something, it is shown in italics in the Explanation and Action column. The messages are listed in alphabetical order. Message Alignment error Continue ! Calibrate error Continue ! Calibration done Continue ! Close roll cover Continue ! Create pattern ! Measure pattern ! Edge not found Reload media Lift lever Load arrow edge print side down Load cancelled Remove media Load error Remove media Load media to align cartridges Lower lever after aligning Explanation and Action The alignment procedure has failed. Check that an opaque media is loaded. Press ↓ to continue and force the automatic alignment procedure again by reseating any of the print cartridges. Do not lift the window while cartridge alignment is being performed. The calibration plot was loaded incorrectly and it could not be measured. Press ↓ to continue, then reload the plot for measurement. Follow front panel instructions. Accuracy calibration is complete. Press ↓ to continue. Rewind the media to take up any slack in the roll, close the roll cover, then press ↓ to continue. Press ↑ to create the pattern for automatic calibration. Press ↓ to start the automatic calibration. The plotter could not find edge of media during loading procedure. Check the leading edge of the media for unevenness or tears; cut a straight edge, if necessary, and reload. Be sure to position the right edge along the perforated line on the entry platen when loading. Lift the lever at the right of the plotter. Remove calibration plot, turn it so that the edge with arrows printed on it is print side down, then load that edge into the plotter. You pressed the Cancel button while media loading was in progress. Remove media. You inserted media with the media lever raised. Lower the lever and reload the media. Load media to proceed with cartridge alignment. When you have finished aligning the roll media as instructed, lower the lever at the right of the plotter. 10-2

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
10-2
Front-Panel Messages
This is a list of all possible messages in the front-panel display.
If you need to do
something, it is shown in
italics
in the
Explanation and
Action
column.
The messages are listed in alphabetical order.
Message
Explanation and
Action
Alignment error
Continue
!
The alignment procedure has failed.
Check that an opaque media is loaded.
Press
↓
to continue and force the automatic alignment procedure again by
reseating any of the print cartridges. Do not lift the window while cartridge
alignment is being performed
.
Calibrate error
Continue
!
The calibration plot was loaded incorrectly and it could not be measured.
Press
↓
to continue, then reload the plot for measurement. Follow front panel instructions.
Calibration done
Continue
!
Accuracy calibration is complete.
Press
↓
to continue.
Close roll cover
Continue
!
Rewind the media to take up any slack in the roll, close the roll cover, then
press
↓
to continue.
Create pattern
!
Measure pattern
!
Press
↑
to create the pattern for automatic calibration.
Press
↓
to start the automatic calibration.
Edge not found
Reload media
The plotter could not find edge of media during loading procedure.
Check the
leading edge of the media for unevenness or tears; cut a straight edge, if
necessary, and reload. Be sure to position the right edge along the perforated line
on the entry platen when loading.
Lift lever
Lift the lever at the right of the plotter.
Load arrow edge
print side down
Remove calibration plot, turn it so that the edge with arrows printed on it is print
side down, then load that edge into the plotter.
Load cancelled
Remove media
You pressed the
Cancel
button while media loading was in progress.
Remove
media.
Load error
Remove media
You inserted media with the media lever raised.
Lower the lever and reload the
media.
Load media
to align cartridges
Load media to proceed with cartridge alignment.
Lower lever
after aligning
When you have finished aligning the roll media as instructed, lower the lever at
the right of the plotter.
Front-Panel Messages