HP 750c HP DesignJet 755CM Printer User's Guide - C3198-60051 - Page 81
the end cap still removed
 |
View all HP 750c manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 81 highlights
Working with Media and Cartridges Loading Media 5 From the other end of the old roll, pull out the endcap (B). B 0022 6 If you are not immediately loading another roll of media into the printer, replace the endcap on the spindle and place the spindle back in the printer. You can skip the rest of these steps. 7 a Remove the new roll from its wrapping. b Turn the spindle upside down, that is, with the media stop at the bottom (and the end cap still removed) c Place the new roll on the spindle, so that the leading edge winds clockwise. Endcap removed MEDIA AND 3 CARTRIDGES If the media stop falls off, push it back A in until it snaps into position. 0015 3-11
-
1 -
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76 -
77 -
78 -
79 -
80 -
81 -
82 -
83 -
84 -
85 -
86 -
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179
-
180
-
181
-
182
-
183
-
184
-
185
-
186
-
187
-
188
-
189
-
190
-
191
-
192
-
193
-
194
-
195
-
196
-
197
-
198
-
199
-
200
-
201
-
202
-
203
-
204
-
205
-
206
-
207
-
208
-
209
-
210
-
211
-
212
-
213
-
214
-
215
-
216
-
217
-
218
-
219
-
220
 |
 |
3-11
5
From the other end of the old roll, pull out the endcap (B).
B
0022
6
If you are not immediately loading another roll of media into the printer
, replace
the endcap on the spindle and place the spindle back in the printer.
You can skip
the rest of these steps.
7
a
Remove the
new roll
from its wrapping.
b
Turn the spindle upside down, that is, with the media stop at the bottom (and
the end cap still removed)
c
Place the new roll on the spindle, so that the leading edge winds
clockwise.
If the media stop falls off, push it back
in until it snaps into position.
Endcap removed
A
0015
Working with Media and Cartridges
Loading Media
MEDIA AND
CARTRIDGES
3