HP Integrity rx2620 Installation Guide, Third Edition - HP Integrity rx2620 (A - Page 47

Installing an Additional Power Supply, Installing a PCI Card

Get HP Integrity rx2620 PDF manuals and user guides View all HP Integrity rx2620 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

Installing Additional Components Installing an Additional Power Supply Step 4. Grasp the edges of the PCI card you are installing, and gently press the card into the PCI backplane connector. Figure 3-14 shows how to install a PCI card. Figure 3-14 Installing a PCI Card Step 5. Reinstall the PCI cage. See "Installing PCI Cards" on page 46. Step 6. Connect any internal cables that are required by the PCI card. Step 7. Install the top metal cover, unless you are installing more components. See "Replacing the Top Metal Cover" on page 36. Installing an Additional Power Supply The supported configuration of an HP Integrity rx2620 server requires a minimum of one power supply unit (PSU). You can install a second hot-swap PSU to provide redundant (N+1) capability. The power supplies in the HP server are hot-swappable. If one power supply stops working or exhibits voltage problems, the remaining supply can support the system until you replace the failed unit. You can remove and replace a power supply without turning off the server on servers with two power supplies. CAUTION Before removing a power supply, make sure the second power supply is functioning properly. Check the two green LEDs inside the second power supply. If they are illuminated, the second power supply is on and able to power the server. You can safely remove the failed power supply. To install the power supply, perform the following steps: Chapter 3 47

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
Chapter 3
Installing Additional Components
Installing an Additional Power Supply
47
Step 4.
Grasp the edges of the PCI card you are installing, and gently press the card into the PCI
backplane connector. Figure 3-14 shows how to install a PCI card.
Figure 3-14 Installing a PCI Card
Step 5.
Reinstall the PCI cage. See “Installing PCI Cards” on page 46.
Step 6.
Connect any internal cables that are required by the PCI card.
Step 7.
Install the top metal cover, unless you are installing more components. See “Replacing the Top
Metal Cover” on page 36.
Installing an Additional Power Supply
The supported configuration of an HP Integrity rx2620 server requires a minimum of one power supply unit
(PSU). You can install a second hot-swap PSU to provide redundant (N+1) capability.
The power supplies in the HP server are hot-swappable. If one power supply stops working or exhibits voltage
problems, the remaining supply can support the system until you replace the failed unit. You can remove and
replace a power supply without turning off the server on servers with two power supplies.
CAUTION
Before removing a power supply, make sure the second power supply is functioning properly.
Check the two green LEDs inside the second power supply. If they are illuminated, the second
power supply is on and able to power the server. You can safely remove the failed power supply.
To install the power supply, perform the following steps: