IBM 4332-004 User Guide - Page 254

STAPLER / CHECK STAPLES, Meaning, Action, Pause, Cancel Print, STAPLER / CHECK CART, LOAD <paper&

Get IBM 4332-004 - InfoPrint 40 B/W Laser Printer PDF manuals and user guides
UPC - 087944489719
View all IBM 4332-004 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 254 highlights

009 STAPLER / CHECK STAPLES Meaning: The 2000-Sheet Finisher staple cartridge is either empty or there is a staple jam. Action: 1. Press the Pause button on the 2000-Sheet Finisher to suspend the finishing operation, or the Cancel Print key on the operator panel to cancel the job. Note: When the stapler is jammed or out of staples, the printer continues sending jobs to the 2000-Sheet Finisher. The jobs will not be stapled even though stapling was requested. 2. Open Cover H, remove the staple cartridge, remove any jammed staples or replenish the staples if the cartridge is empty. See"Replenishing Staples in the 2000-Sheet Finisher" on page 149. 3. Press the Pause button again to resume printing, or if you used the Cancel Print key, resubmit your job. 010 STAPLER / CHECK CART Meaning: The staple cartridge is either missing or not seated properly. Action: Open Cover H, and reseat the staple cartridge. 011 LOAD / IN Meaning: The tray is out of paper, the tray contains the wrong size paper, or the tray is loaded incorrectly. The message identifies the size of paper (paper) and the tray ( tray) that needs paper. (ANY indicates you can load any tray that supports the paper size.) If the message indicates a tray you did not specify, either the original tray is out of paper and automatic tray switching is enabled, or the original tray contains the wrong size paper. (Tray switching is automatic for paper size mismatches. See "Turning Tray Switching On or Off" on page 66.) Actions: v If the tray is empty, refill it. After a few seconds, the printer resumes printing on its own. v If the tray contains the wrong size paper, you have two choices: 1. To use the current paper size, press the Continue key. 2. Load the correct paper size into the tray. v If the tray contains the correct size paper, make sure the paper is loaded correctly. Check the paper guides. The AUTOSENSED PAPER section of the printer configuration page shows what size paper the printer paper size sensors have determined is in each tray. See "Printing the Printer Configuration Page" on page 25. v If you specified a different tray, and you do not want to use the tray specified in the message, you can do the following: 242 Infoprint 32 and Infoprint 40: User's Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
  • 254
  • 255
  • 256
  • 257
  • 258
  • 259
  • 260
  • 261
  • 262
  • 263
  • 264
  • 265
  • 266
  • 267
  • 268
  • 269
  • 270
  • 271
  • 272
  • 273
  • 274
  • 275
  • 276
  • 277
  • 278
  • 279
  • 280
  • 281
  • 282
  • 283
  • 284
  • 285
  • 286
  • 287
  • 288
  • 289
  • 290
  • 291
  • 292
  • 293
  • 294
  • 295
  • 296
009 STAPLER / CHECK STAPLES
Meaning
: The 2000-Sheet Finisher staple cartridge is either empty or
there is a staple jam.
Action
:
1.
Press the
Pause
button on the 2000-Sheet Finisher to suspend the
finishing operation, or the
Cancel Print
key on the operator panel
to cancel the job.
Note:
When the stapler is jammed or out of staples, the printer
continues sending jobs to the 2000-Sheet Finisher. The jobs
will not be stapled even though stapling was requested.
2.
Open Cover H, remove the staple cartridge, remove any jammed
staples or replenish the staples if the cartridge is empty.
See“Replenishing Staples in the 2000-Sheet Finisher” on page 149.
3.
Press the
Pause
button again to resume printing, or if you used
the
Cancel Print
key, resubmit your job.
010 STAPLER / CHECK CART
Meaning
: The staple cartridge is either missing or not seated properly.
Action
: Open Cover H, and reseat the staple cartridge.
011 LOAD <paper> / IN <tray>
Meaning
: The tray is out of paper, the tray contains the wrong size
paper, or the tray is loaded incorrectly. The message identifies the size
of paper (
paper
) and the tray (
tray
) that needs paper. (ANY indicates
you can load any tray that supports the paper size.) If the message
indicates a tray you did not specify, either the original tray is out of
paper and automatic tray switching is enabled, or the original tray
contains the wrong size paper. (Tray switching is automatic for paper
size mismatches. See “Turning Tray Switching On or Off” on page 66.)
Actions
:
v
If the tray is empty, refill it. After a few seconds, the printer
resumes printing on its own.
v
If the tray contains the wrong size paper, you have two choices:
1.
To use the current paper size, press the
Continue
key.
2.
Load the correct paper size into the tray.
v
If the tray contains the correct size paper, make sure the paper is
loaded correctly. Check the paper guides. The AUTOSENSED
PAPER section of the printer configuration page shows what size
paper the printer paper size sensors have determined is in each
tray. See “Printing the Printer Configuration Page” on page 25.
v
If you specified a different tray, and you do not want to use the
tray specified in the message, you can do the following:
242
Infoprint 32 and Infoprint 40: User’s Guide