IBM JS20 Hardware Maintenance Manual - Page 99

Installing

Get IBM JS20 - BladeCenter - 8842 PDF manuals and user guides
UPC - 000435230263
View all IBM JS20 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 99 highlights

assembly, the firmware code will request that you enter the serial number, as described in step 16. You must enter the blade-server serial number. If you enter a different serial number, the operating system that you installed might interpret this information as an incorrect serial number, and you might have to change your software-licensing agreement. v To maintain proper airflow, do not place the new label on the blade-server bezel assembly. Also, be sure to place the RID tag label on the bottom of the blade server chassis. 11. Install the blade-server bezel assembly on the blade server (see "Installing the blade-server bezel assembly" on page 90). 12. Close the blade server cover (see "Closing the blade server cover" on page 92). Statement 21: CAUTION: Hazardous energy is present when the blade server is connected to the power source. Always replace the blade cover before installing the blade server. 13. Install the blade server into the same BladeCenter unit I/O bay from which you removed the blade server when it contained the faulty system-board assembly. 14. Turn on the blade server (see "Turning on the blade server" on page 13). Note: If you have just connected the power cords of the BladeCenter unit to electrical outlets, you will have to wait until the power-on LED on the blade server slowly flashes before you press the power-control button on the blade server. 15. Configure an SOL connection and attach it to this blade server. For additional information, see the IBM BladeCenter and Eserver BladeCenter T Serial Over LAN Setup Guide. 16. The blade server will boot to the open firmware command to enter the serial number of the blade server (with the original system-board assembly). The blade server will not start until the serial number and other relevant information have been entered and verified at the prompts when the following checkpoint codes are displayed, as shown in the following example window. Depending on the blade server configuration, the text that is displayed in your system window might be slightly different. E1F0 E1F1 D099 D100 > xxxxxxx (The serial number of the blade server with the original system-board assembly) D101 > xxxxxxx (Re-enter the serial number to verify) D102 > 8842 (The type number from the blade server) D103 > 8842 (Re-enter the type number to verify) D104 > xxxx (The model number from the blade server) D105 > xxxx (Re-enter the model number to verify) Chapter 9. Installing options 89

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
assembly,
the
firmware
code
will
request
that
you
enter
the
serial
number,
as
described
in
step
16.
You
must
enter
the
blade-server
serial
number.
If
you
enter
a
different
serial
number,
the
operating
system
that
you
installed
might
interpret
this
information
as
an
incorrect
serial
number,
and
you
might
have
to
change
your
software-licensing
agreement.
v
To
maintain
proper
airflow,
do
not
place
the
new
label
on
the
blade-server
bezel
assembly.
Also,
be
sure
to
place
the
RID
tag
label
on
the
bottom
of
the
blade
server
chassis.
11.
Install
the
blade-server
bezel
assembly
on
the
blade
server
(see
“Installing
the
blade-server
bezel
assembly”
on
page
90).
12.
Close
the
blade
server
cover
(see
“Closing
the
blade
server
cover”
on
page
92).
Statement
21:
CAUTION:
Hazardous
energy
is
present
when
the
blade
server
is
connected
to
the
power
source.
Always
replace
the
blade
cover
before
installing
the
blade
server.
13.
Install
the
blade
server
into
the
same
BladeCenter
unit
I/O
bay
from
which
you
removed
the
blade
server
when
it
contained
the
faulty
system-board
assembly.
14.
Turn
on
the
blade
server
(see
“Turning
on
the
blade
server”
on
page
13).
Note:
If
you
have
just
connected
the
power
cords
of
the
BladeCenter
unit
to
electrical
outlets,
you
will
have
to
wait
until
the
power-on
LED
on
the
blade
server
slowly
flashes
before
you
press
the
power-control
button
on
the
blade
server.
15.
Configure
an
SOL
connection
and
attach
it
to
this
blade
server.
For
additional
information,
see
the
IBM
Eserver
BladeCenter
and
BladeCenter
T
Serial
Over
LAN
Setup
Guide
.
16.
The
blade
server
will
boot
to
the
open
firmware
command
to
enter
the
serial
number
of
the
blade
server
(with
the
original
system-board
assembly).
The
blade
server
will
not
start
until
the
serial
number
and
other
relevant
information
have
been
entered
and
verified
at
the
prompts
when
the
following
checkpoint
codes
are
displayed,
as
shown
in
the
following
example
window.
Depending
on
the
blade
server
configuration,
the
text
that
is
displayed
in
your
system
window
might
be
slightly
different.
E1F0
E1F1
D099
D100
>
xxxxxxx
(The
serial
number
of
the
blade
server
with
the
original
system-board
assembly)
D101
>
xxxxxxx
(Re-enter
the
serial
number
to
verify)
D102
>
8842
(The
type
number
from
the
blade
server)
D103
>
8842
(Re-enter
the
type
number
to
verify)
D104
>
xxxx
(The
model
number
from
the
blade
server)
D105
>
xxxx
(Re-enter
the
model
number
to
verify)
Chapter
9.
Installing
options
89