Icom IC-7800 Instruction Manual - Page 182

CONTROL COMMAND 14 D Command table Command 00 01 02 03 04 05 06 07 08 09 0A 0B 0E 0F 10 Sub command Description - Send frequency data Same as Send mode data command 06 - Read band edge frequencies - Read operating frequency - Read operating mode - Set operating frequency 00 Select LSB 01 Select USB 02 Select AM 03 Select CW 04 Select RTTY 05 Select FM 07 Select CW-R 08 Select RTTY-R 12 Select PSK 13 Select PSK-R - Select VFO mode B0 Exchange main and sub bands B1 Equalize main and sub bands C0 Turn the dualwatch OFF C1 Turn the dualwatch ON D0 Select main band D1 Select sub band - 0001-0101* Select memory mode Select memory channel *P1=0100, P2=0101 - Memory write - Memory to VFO - Memory clear 00 01 02 03 12 13 22 23 A1-A7 B0 B1 B2 D0 D3 Scan stop Programmed/memory scan start Programmed scan start ∂F scan start Fine programmed scan start Fine ∂F scan start Memory scan start Select memory scan start Set ∂F scan span (A1=±5 kHz; A2=±10 kHz; A3=±20 kHz; A4=±50 kHz; A5=±100 kHz; A6=±500 kHz; A7=±1 MHz) Set as non-select channel Set as select channel (1=#1; 2=#2; 3=#3; when no data command is specified, the previously set number or "#1" is selected) Set the number for select memory scan (0=ALL; 1=#1; 2=#2; 3=#3) Set scan resume OFF Set scan resume ON 00 Turn the split function OFF 01 Turn the split function ON 00 Select 10 Hz (1 Hz) tuning step 01 Select 100 Hz tuning step 02 Select 1 kHz tuning step 03 Select 5 kHz tuning step 04 Select 9 kHz tuning step 05 Select 10 kHz tuning step 06 Select 12.5 kHz tuning step 07 Select 20 kHz tuning step 08 Select 25 kHz tuning step Command 11 12 13 14 Sub command Description - Select/read attenuator (0=OFF; 1=3 dB; 2=6 dB; 3=9 dB; 4=12 dB; 5=15 dB; 6=18 dB; 7=21 dB) 00 + RX ANT 01 + RX ANT 02 + RX ANT 03 + RX ANT Select/read ANT1 selection (00=RX ANT OFF; 01=RX ANT ON) Select/read ANT2 selection (00=RX ANT OFF; 01=RX ANT ON) Select/read ANT3 selection (00=RX ANT OFF; 01=RX ANT ON) Select/read ANT4 selection (00=RX ANT OFF; 01=RX ANT ON) 00 Announce with voice synthesizer 01 (00=all data; 01=frequency and 02 S-meter level; 02=receive mode) 01 + Level data [AF] level setting (0=max. CCW to 255=max. CW) 02 + Level data [RF] level setting (0=max. CCW to 255=11 o'clock) 03 + Level data [SQL] level setting (0=11 o'clock to 255=max. CW) 05 + Level data [APF] level setting (0=Pitch-550 Hz, 128=Pitch, 255=Pitch+550 Hz; 10 Hz steps) 06 + Level data [NR] level setting (0=min. to 255=max.) 07 + Level data Inside [TWIN PBT] setting or IF shift setting (0=max. CCW, 128=center, 255=max. CW) 08 + Level data Outside [TWIN PBT] setting (0=max. CCW, 128=center, 255=max. CW) 09 + Level data [CW PITCH] setting (0=300 Hz, 128=600 Hz, 255=900 Hz; 5 Hz steps) 0A + Level data [RF POWER] setting (0=max. CCW to 255=max. CW) 0B + Level data [MIC] setting (0=max. CCW to 255=max. CW) 0C + Level data [KEY SPEED] setting (0=max. CCW to 255=max. CW) 0D + Level data [NOTCH] setting (0=low freq. to 255=high freq.) 0E + Level data [COMP] setting (0=max. CCW to 255=max. CW) 0F + Level data [DELAY] setting (0=max. CCW to 255=max. CW) 11 + Level data [AGC] control setting (0=max. CCW to 255=max. CW) 12 + Level data [NB] control setting (0=max. CCW to 255=max. CW) 13 + Level data [DIGI-SEL] setting (0=max. CCW to 255=max. CW) 14 + Level data [DRIVE] setting (0=max. CCW to 255=max. CW) 15 + Level data [MONI GAIN] setting (0=max. CCW to 255=max. CW) 16 + Level data [VOX GAIN] setting (0=max. CCW to 255=max. CW) 17 + Level data [ANTI VOX] setting (0=max. CCW to 255=max. CW) 18 + Level data [CONTRAST] setting (0=max. CCW to 255=max. CW) 19 + Level data [BRIGHT] setting (0=max. CCW to 255=max. CW) 14-3