Lenovo ThinkPad X1 (English) User Guide - Page 143

Error messages, Bad CRC of Security Settings in EFI Variable. Enter ThinkPad Setup.

Page 143 highlights

If you spill something on your computer: Attention: Be sure that no liquid creates a short circuit between you and the ac power adapter (if in use). Although you might lose some data or work by turning off the computer immediately, leaving the computer on might make your computer unusable. 1. Carefully unplug the ac power adapter immediately. 2. Turn off the computer immediately. If the computer does not turn off, reset the system by inserting one end of a needle or a straightened paper clip into the emergency reset hole. The more quickly you stop the current from passing through the computer the more likely you will reduce damage from short circuits. 3. Wait until you are certain that all the liquid is dry before turning on your computer. Note: If you want to replace your keyboard, you can purchase a new one. Error messages Message: 0176: System Security - The System has been tampered with. Solution: This message is displayed if you remove the Security Chip and reinstall it, or install a new one. To clear the error, enter the ThinkPad Setup. If this does not solve the problem, have the computer serviced. Message: 0177: Bad SVP data, stop POST task. Solution: Checksum of the supervisor password in the EEPROM is not correct. The system board should be replaced. Have the computer serviced. Message: 0182: Bad CRC of Security Settings in EEPROM. Enter ThinkPad Setup. Solution: Checksum of the Security settings in the EEPROM is not correct. Enter ThinkPad Setup to check Security settings, Press F10 and then press Enter to restart the system. If you still have a problem, have the computer serviced. Message: 0183: Bad CRC of Security Settings in EFI Variable. Enter ThinkPad Setup. Solution: Checksum of the Security settings in the EFI Variable is not correct. Enter ThinkPad Setup to check Security settings, Press F10 and then press Enter to restart the system. If you still have a problem, have the computer serviced. Message: 0187: EAIA data access error Solution: The access to EEPROM is failed. Have the computer serviced. Message: 0188: Invalid RFID Serialization Information Area. Solution: The EEPROM checksum is not correct (block # 0 and 1). The system board should be replaced, and the box serial number needs to be reinstalled. Have the computer serviced. Message: 0189: Invalid RFID configuration information area Solution: The EEPROM checksum is not correct (block # 4 and 5). The system board should be replaced, and the UUID needs to be reinstalled. Have the computer serviced. Message: 0190: Critical low-battery error Chapter 10. Troubleshooting computer problems 127

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181

If you spill something on your computer:
Attention:
Be sure that no liquid creates a short circuit between you and the ac power adapter (if in use).
Although you might lose some data or work by turning off the computer immediately, leaving the computer
on might make your computer unusable.
1. Carefully unplug the ac power adapter immediately.
2. Turn off the computer immediately. If the computer does not turn off, reset the system by inserting one
end of a needle or a straightened paper clip into the emergency reset hole. The more quickly you stop the
current from passing through the computer the more likely you will reduce damage from short circuits.
3. Wait until you are certain that all the liquid is dry before turning on your computer.
Note:
If you want to replace your keyboard, you can purchase a new one.
Error messages
Message:
0176: System Security - The System has been tampered with.
Solution:
This message is displayed if you remove the Security Chip and reinstall it, or install a new one. To
clear the error, enter the ThinkPad Setup. If this does not solve the problem, have the computer serviced.
Message:
0177: Bad SVP data, stop POST task.
Solution:
Checksum of the supervisor password in the EEPROM is not correct. The system board should be
replaced. Have the computer serviced.
Message:
0182: Bad CRC of Security Settings in EEPROM. Enter ThinkPad Setup.
Solution:
Checksum of the Security settings in the EEPROM is not correct. Enter ThinkPad Setup to
check Security settings, Press F10 and then press Enter to restart the system. If you still have a problem,
have the computer serviced.
Message:
0183: Bad CRC of Security Settings in EFI Variable. Enter ThinkPad Setup.
Solution:
Checksum of the Security settings in the EFI Variable is not correct. Enter ThinkPad Setup to
check Security settings, Press F10 and then press Enter to restart the system. If you still have a problem,
have the computer serviced.
Message:
0187: EAIA data access error
Solution:
The access to EEPROM is failed. Have the computer serviced.
Message:
0188: Invalid RFID Serialization Information Area.
Solution:
The EEPROM checksum is not correct (block # 0 and 1). The system board should be replaced,
and the box serial number needs to be reinstalled. Have the computer serviced.
Message:
0189: Invalid RFID configuration information area
Solution:
The EEPROM checksum is not correct (block # 4 and 5). The system board should be replaced,
and the UUID needs to be reinstalled. Have the computer serviced.
Message:
0190: Critical low-battery error
Chapter 10
.
Troubleshooting computer problems
127