Nokia 6600 Nokia 6600 User Guide in English - Page 20

Charging the battery, Switching the phone on (or off), Antenna, TIPS ON EFFICIENT OPERATION

Get Nokia 6600 PDF manuals and user guides
UPC - 738642184368
View all Nokia 6600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

General information Charging the battery 1 Connect the power cord to the charger. You will hear it click into place. 2 Connect the charger to an AC wall outlet. 3 Connect the power cord from the charger to the base of the phone (10). The battery indicator bar starts 10 scrolling. Note that you can use the phone while charging. 4 When the battery is fully charged, the bar stops scrolling. Disconnect the charger from the AC outlet and then from the phone. See the 'Battery information' chapter. Switching the phone on (or off) Press and hold the power key . Antenna TIPS ON EFFICIENT OPERATION Your phone has a built-in antenna (highlighted area in picture). As with any other radio transmitting device, do not touch the antenna unnecessarily when the phone is switched on. Contact with the antenna affects call quality and may cause the phone to operate at a higher power level than otherwise needed. Avoiding contact with the antenna area when operating the phone optimizes the antenna performance and the battery life. NORMAL POSITION Hold the phone as you would any other telephone with the antenna pointed up and over your shoulder. IF THE PHONE REQUESTS A PIN CODE: The PIN code is usually supplied with the SIM card. • Key in the code (displayed as ****) and press . Nokia 6600 User Guide 7 Copyright © 2004 Nokia

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
Nokia 6600 User Guide
7
Copyright © 2004 Nokia
General information
Charging the battery
1
Connect the power cord to the charger.
You will hear it click into place.
2
Connect the charger to an AC
wall outlet.
3
Connect the power cord from the
charger to the base of the phone (
10
).
The battery indicator bar starts
scrolling. Note that you can use
the phone while charging.
4
When the battery is fully charged, the bar stops scrolling. Disconnect the
charger from the AC outlet and then from the phone. See the
’
Battery
information
’
chapter.
Switching the phone on (or off)
Press and hold the power key
Antenna
TIPS ON EFFICIENT OPERATION
Your phone has a built-in antenna (highlighted area
in picture). As with any other radio transmitting device,
do not touch the antenna unnecessarily when the
phone is switched on. Contact with the antenna
affects call quality and may cause the phone to
operate at a higher power level than otherwise
needed. Avoiding contact with the antenna area
when operating the phone optimizes the antenna
performance and the battery life.
NORMAL POSITION
Hold the phone as you would any other telephone
with the antenna pointed up and over your shoulder.
IF THE PHONE REQUESTS A PIN CODE:
The PIN code is usually supplied with the SIM card.
•
Key in the code (displayed as ****) and press
.
10