Dell Latitude 7030 Rugged Extreme Tablet Owners Manual - Page 125

Installing the display assembly

Get Dell Latitude 7030 Rugged Extreme Tablet PDF manuals and user guides View all Dell Latitude 7030 Rugged Extreme Tablet manuals
Add to My Manuals
Save this manual to your list of manuals

Page 125 highlights

NOTE: The RJ45 port/USB port/audio jack bezel that is removed from the faulty display assembly must be replaced in the replacement display assembly. 3. After performing the above mentioned steps, you are left with the display assembly. NOTE: The M.2 SSD absorber and thermal pad are reusable and are required to be transferred onto the new display assembly for any display-assembly replacement. NOTE: The display assembly cannot be further disassembled. If any components in the display assembly are malfunctioning and are required to be replaced, replace the entire display assembly. Installing the display assembly CAUTION: The information in this installation section is intended for authorized service technicians only. Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The following images indicate the location of the display assembly and provide a visual representation of the installation procedure. Figure 109. Installing the display assembly Steps 1. Place the tablet on a flat and clean surface. 2. Align and place the RJ45 port/USB port/audio jack bezel on the display assembly. Removing and installing Field Replaceable Units (FRUs) 125

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
NOTE:
The RJ45 port/USB port/audio jack bezel that is removed from the faulty display assembly must be replaced in
the replacement display assembly.
3.
After performing the above mentioned steps, you are left with the display assembly.
NOTE:
The M.2 SSD absorber and thermal pad are reusable and are required to be transferred onto the new display
assembly for any display-assembly replacement.
NOTE:
The display assembly cannot be further disassembled. If any components in the display assembly are
malfunctioning and are required to be replaced, replace the entire display assembly.
Installing the display assembly
CAUTION:
The information in this installation section is intended for authorized service technicians only.
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following images indicate the location of the display assembly and provide a visual representation of the installation
procedure.
Figure 109. Installing the display assembly
Steps
1.
Place the tablet on a flat and clean surface.
2.
Align and place the RJ45 port/USB port/audio jack bezel on the display assembly.
Removing and installing Field Replaceable Units (FRUs)
125