Dell Latitude 7030 Rugged Extreme Tablet Owners Manual - Page 61

Installing the base-cover assembly

Get Dell Latitude 7030 Rugged Extreme Tablet PDF manuals and user guides View all Dell Latitude 7030 Rugged Extreme Tablet manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

CAUTION: Do not open the back-cover assembly beyond a 90-degree angle as it damages the battery cable and power-button daughter-board FPC. Both the cables (the battery cable and power-button daughter-board FPC) must be disconnected in order to remove the back-cover assembly. 5. Disconnect the battery cable from the connector on the system board and then open the back cover to a full angle. 6. Flip over the back-cover assembly and place it on a flat surface. Figure 51. Removing the base-cover assembly 7. Remove the two screws (M2x3) that secure the power-button daughter board FPC to the system board. 8. Disconnect the power-button daughter-board FPC from the connector system board. 9. Remove the back-cover assembly away from the tablet. Installing the base-cover assembly Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The following images indicate the location of the base-cover assembly and provide a visual representation of the installation procedure. Removing and installing Field Replaceable Units (FRUs) 61

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
CAUTION:
Do not open the back-cover assembly beyond a 90-degree angle as it damages the battery cable
and power-button daughter-board FPC. Both the cables (the battery cable and power-button daughter-board
FPC) must be disconnected in order to remove the back-cover assembly.
5.
Disconnect the battery cable from the connector on the system board and then open the back cover to a full angle.
6.
Flip over the back-cover assembly and place it on a flat surface.
Figure 51. Removing the base-cover assembly
7.
Remove the two screws (M2x3) that secure the power-button daughter board FPC to the system board.
8.
Disconnect the power-button daughter-board FPC from the connector system board.
9.
Remove the back-cover assembly away from the tablet.
Installing the base-cover assembly
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following images indicate the location of the base-cover assembly and provide a visual representation of the installation
procedure.
Removing and installing Field Replaceable Units (FRUs)
61