Dell Latitude 7030 Rugged Extreme Tablet Owners Manual - Page 84

USB-port assembly, Removing the USB-port assembly

Get Dell Latitude 7030 Rugged Extreme Tablet PDF manuals and user guides View all Dell Latitude 7030 Rugged Extreme Tablet manuals
Add to My Manuals
Save this manual to your list of manuals

Page 84 highlights

4. Connect the RJ45-port daughter-board to the connector on the system board. 5. Replace the two screws (M1x2.65) to secure the RJ45-port daughter-board to the system board. Next steps 1. Install the back-cover assembly. 2. Install the hot-swappable batteries, if applicable. 3. Install the handle, if applicable. 4. Install the stylus. 5. Follow the procedure in After working inside your tablet. USB-port assembly Removing the USB-port assembly CAUTION: The information in this removal section is intended for authorized service technicians only. NOTE: This procedure applies only to tablets shipped with a USB connector installed in the expansion bay at the top side of the tablet. Prerequisites 1. Follow the procedure in Before working inside your tablet. 2. Remove the stylus. 3. Remove the handle, if applicable. 4. Remove the hot-swappable batteries, if applicable. 5. Remove the back-cover assembly. About this task The following images indicate the location of the USB-port assembly and provide a visual representation of the removal procedure. 84 Removing and installing Field Replaceable Units (FRUs)

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
4.
Connect the RJ45-port daughter-board to the connector on the system board.
5.
Replace the two screws (M1x2.65) to secure the RJ45-port daughter-board to the system board.
Next steps
1.
Install the
back-cover assembly
.
2.
Install the
hot-swappable batteries
, if applicable.
3.
Install the
handle
, if applicable.
4.
Install the
stylus
.
5.
Follow the procedure in
After working inside your tablet
.
USB-port assembly
Removing the USB-port assembly
CAUTION:
The information in this removal section is intended for authorized service technicians only.
NOTE:
This procedure applies only to tablets shipped with a USB connector installed in the expansion bay at the top side of
the tablet.
Prerequisites
1.
Follow the procedure in
Before working inside your tablet
.
2.
Remove the
stylus
.
3.
Remove the
handle
, if applicable.
4.
Remove the
hot-swappable batteries
, if applicable.
5.
Remove the
back-cover assembly
.
About this task
The following images indicate the location of the USB-port assembly and provide a visual representation of the removal
procedure.
84
Removing and installing Field Replaceable Units (FRUs)