Dell Latitude 7030 Rugged Extreme Tablet Owners Manual - Page 79

Installing the front camera and microphone assembly

Get Dell Latitude 7030 Rugged Extreme Tablet PDF manuals and user guides View all Dell Latitude 7030 Rugged Extreme Tablet manuals
Add to My Manuals
Save this manual to your list of manuals

Page 79 highlights

2. Remove the two screws (M2x3) that secure the front camera and microphone assembly to the display assembly. 3. Remove the front camera and microphone assembly from the display assembly. Installing the front camera and microphone assembly CAUTION: The information in this installation section is intended for authorized service technicians only. Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The following images indicate the location of the front camera and microphone assembly and provide a visual representation of the installation procedure. Figure 67. Installing the front camera and microphone assembly Steps NOTE: Latitude 7030 Rugged Extreme Tablet features three configurations for the front camera and microphone assembly: a. Front camera and microphone assembly b. Microphone and bracket (without front camera) c. Bracket only (without front camera and microphone) NOTE: If any component in the front camera and microphone assembly is faulty, replace the entire assembly. 1. Align the screw holes on the front camera and microphone assembly with the screw holes on the display assembly. 2. Replace the two screws (M2x3) to secure the front camera and microphone assembly to the display assembly. 3. Connect the front-camera FPC or microphone FPC to the connector on the system board. NOTE: This step applies only to configurations a and b listed above. Removing and installing Field Replaceable Units (FRUs) 79

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
2.
Remove the two screws (M2x3) that secure the front camera and microphone assembly to the display assembly.
3.
Remove the front camera and microphone assembly from the display assembly.
Installing the front camera and microphone assembly
CAUTION:
The information in this installation section is intended for authorized service technicians only.
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following images indicate the location of the front camera and microphone assembly and provide a visual representation of
the installation procedure.
Figure 67. Installing the front camera and microphone assembly
Steps
NOTE:
Latitude 7030 Rugged Extreme Tablet features three configurations for the front camera and microphone assembly:
a.
Front camera and microphone assembly
b.
Microphone and bracket (without front camera)
c.
Bracket only (without front camera and microphone)
NOTE:
If any component in the front camera and microphone assembly is faulty, replace the entire assembly.
1.
Align the screw holes on the front camera and microphone assembly with the screw holes on the display assembly.
2.
Replace the two screws (M2x3) to secure the front camera and microphone assembly to the display assembly.
3.
Connect the front-camera FPC or microphone FPC to the connector on the system board.
NOTE:
This step applies only to configurations a and b listed above.
Removing and installing Field Replaceable Units (FRUs)
79