Dell PowerVault NX3500 Hardware Owner's Manual - Page 37

NVRAM_CLR jumper, Please run SETUP.

Get Dell PowerVault NX3500 PDF manuals and user guides View all Dell PowerVault NX3500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

Table 1-4. System Messages (continued) Message Causes Corrective Actions Alert! System fatal error during previous boot. An error caused the system to Check other system reboot. messages for additional information for possible causes. BIOS MANUFACTURING MODE detected. MANUFACTURING MODE will be cleared before the next boot. System reboot required for normal operation. System is in manufacturing Reboot to take the system mode. out of manufacturing mode. BIOS Update Remote BIOS update Attempt Failed! attempt failed. Retry the BIOS update. If the problem persists, see "Getting Help" on page 113. Caution! NVRAM_CLR jumper is NVRAM_CLR jumper installed in the clear setting. is installed on CMOS has been cleared. system board. Please run SETUP. Move the NVRAM_CLR jumper to the default position (pins 3 and 5). See Figure 5-1 for jumper location. CPU set to minimum frequency. The processor speed may be If not an intentional setting, intentionally set lower for check any other system power conservation. messages for possible causes. About Your Solution 37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
About Your Solution
37
Alert! System
fatal error
during previous
boot.
An error caused the system to
reboot.
Check other system
messages for additional
information for possible
causes.
BIOS
MANUFACTURING
MODE detected.
MANUFACTURING
MODE will be
cleared before
the next boot.
System reboot
required for
normal
operation.
System is in manufacturing
mode.
Reboot to take the system
out of manufacturing mode.
BIOS Update
Attempt Failed!
Remote BIOS update
attempt failed.
Retry the BIOS update.
If the problem persists,
see "Getting Help" on
page 113.
Caution!
NVRAM_CLR jumper
is installed on
system board.
Please run SETUP.
NVRAM_CLR jumper is
installed in the clear setting.
CMOS has been cleared.
Move the NVRAM_CLR
jumper to the default
position (pins 3 and 5).
See Figure 5-1 for jumper
location.
CPU set to
minimum
frequency.
The processor speed may be
intentionally set lower for
power conservation.
If not an intentional setting,
check any other system
messages for possible causes.
Table 1-4.
System Messages
(continued)
Message
Causes
Corrective Actions