Dell PowerVault NX3500 Hardware Owner's Manual - Page 38

Gate A20 failure., Invalid PCIe card

Get Dell PowerVault NX3500 PDF manuals and user guides View all Dell PowerVault NX3500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

Table 1-4. System Messages (continued) Message Causes Corrective Actions Current boot mode The system failed to boot Ensure that the boot mode is is set to UEFI. because UEFI boot mode is set correctly and that the Please ensure enabled in BIOS and the proper bootable media is compatible boot operating system is non- available. bootable media is UEFI. available. Use the system setup program to change the boot mode as needed. Embedded NICx and The OS NIC interface is set NICy: in BIOS. The Management OS NIC=, in management tools. Management Shared NIC= Check the system management software or the System Setup program for NIC settings. If a problem is indicated, see "Troubleshooting a NIC" on page 93. Gate A20 failure. Faulty keyboard controller; See "Getting Help" on faulty system board. page 113. Invalid configuration information please run SETUP program. An invalid system configuration caused a system halt. Run the System Setup program and review the current settings. Invalid PCIe card The system halted because found in the an invalid PCIe expansion Internal_Storage card is installed in the slot! dedicated storage controller slot. Remove the PCIe expansion card and install the integrated storage controller in the dedicated slot. See "Getting Help" on page 113. Keyboard fuse has Overcurrent detected at the See "Getting Help" on failed. keyboard connector. page 113. 38 About Your Solution

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
38
About Your Solution
Current boot mode
is set to UEFI.
Please ensure
compatible
bootable media is
available. Use
the system setup
program to change
the boot mode as
needed.
The system failed to boot
because UEFI boot mode is
enabled in BIOS and the
boot operating system is non-
UEFI.
Ensure that the boot mode is
set correctly and that the
proper bootable media is
available.
Embedded NIC
x
and
NIC
y
:
OS NIC=
<ENABLED
|DISABLED>
,
Management
Shared NIC=
<ENABLED
|DISABLED>
The OS NIC interface is set
in BIOS. The Management
Shared NIC interface is set
in management tools.
Check the system
management software or the
System Setup program for
NIC settings. If a problem is
indicated, see
"Troubleshooting a NIC" on
page 93.
Gate A20 failure.
Faulty keyboard controller;
faulty system board.
See "Getting Help" on
page 113.
Invalid
configuration
information -
please run SETUP
program.
An invalid system
configuration caused a
system halt.
Run the System Setup
program and review the
current settings.
Invalid PCIe card
found in the
Internal_Storage
slot!
The system halted because
an invalid PCIe expansion
card is installed in the
dedicated storage
controller slot.
Remove the PCIe expansion
card and install the
integrated storage controller
in the dedicated slot. See
"Getting Help" on page 113.
Keyboard fuse has
failed.
Overcurrent detected at the
keyboard connector.
See "Getting Help" on
page 113.
Table 1-4.
System Messages
(continued)
Message
Causes
Corrective Actions