Dell PowerVault NX3500 Hardware Owner's Manual - Page 84

cables, and USB cables., Remove the optical drive cable, control panel cable, power cable, data

Get Dell PowerVault NX3500 PDF manuals and user guides View all Dell PowerVault NX3500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 84 highlights

CAUTION: You must note the number of each hard drive and temporarily label them before removal so that you can replace them in the same locations. 3 Remove all hard drives. See "Removing a Hard-Drive Carrier" on page 57. 4 Disconnect the power cable from the SAS backplane. 5 Disconnect the SAS data cables from the backplane. See Figure 2-18. 6 Remove the optical drive cable, control panel cable, power cable, data cables, and USB cables. 7 Press the two blue retention latches at either ends of the SAS backplane and lift it upwards and out of the retention hooks. Be careful to avoid damaging the other components on the face of the board. See Figure 2-18. 8 Place the SAS backplane face down on a work surface. Figure 2-18. Removing and Installing a SAS Backplane 1 2 3 4 5 1 backplane retention latches (2) 3 SAS A cable 5 SAS B cable 2 SAS backplane power cable 4 SAS backplane 84 Installing System Components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
84
Installing System Components
CAUTION:
You must note the number of each hard drive and temporarily label
them before removal so that you can replace them in the same locations.
3
Remove all hard drives. See "Removing a Hard-Drive Carrier" on page 57.
4
Disconnect the power cable from the SAS backplane.
5
Disconnect the SAS data cables from the backplane. See Figure 2-18.
6
Remove the optical drive cable, control panel cable, power cable, data
cables, and USB cables.
7
Press the two blue retention latches at either ends of the SAS backplane
and lift it upwards and out of the retention hooks. Be careful to avoid
damaging the other components on the face of the board. See Figure 2-18.
8
Place the SAS backplane face down on a work surface.
Figure 2-18.
Removing and Installing a SAS Backplane
1
backplane retention latches (2)
2
SAS backplane power cable
3
SAS A cable
4
SAS backplane
5
SAS B cable
1
2
3
4
5