Dell PowerVault NX3500 Hardware Owner's Manual - Page 41

Quad rank DIMM, Plug & Play

Get Dell PowerVault NX3500 PDF manuals and user guides View all Dell PowerVault NX3500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

Table 1-4. System Messages (continued) Message Causes Corrective Actions Plug & Play Configuration Error. Error encountered in initializing PCIe device; faulty system board. Install the NVRAM_CLR jumper in the clear position (pins 1 and 3) and reboot the system. See Figure 5-1 for jumper location. If the problem persists, see "Troubleshooting an Expansion Card" on page 101. Quad rank DIMM detected after single rank or dual rank DIMM in socket. Invalid memory configuration. Ensure that the memory modules are installed in a valid configuration. See "General Memory Module Installation Guidelines" on page 67. Read fault. Requested sector not found. The operating system cannot Replace the optical medium, read from the hard drive, USB medium, or USB optical drive, or USB device, device. Ensure that the USB the system could not find a cables, SAS/SATA backplane particular sector on the disk, cables, or optical drive cables or the requested sector is are properly connected. defective. See "Troubleshooting an Optical Drive" on page 99, or "Troubleshooting a Hard Drive" on page 100 for the appropriate drive(s) installed in your system. SATA Port x device not found. There is no device connected Information only. to the specified SATA port. About Your Solution 41

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
About Your Solution
41
Plug & Play
Configuration
Error.
Error encountered in
initializing PCIe device;
faulty system board.
Install the NVRAM_CLR
jumper in the clear position
(pins 1 and 3) and reboot the
system. See Figure 5-1 for
jumper location. If the
problem persists,
see "Troubleshooting an
Expansion Card" on
page 101.
Quad rank DIMM
detected after
single rank or
dual rank DIMM in
socket.
Invalid memory
configuration.
Ensure that the memory
modules are installed in a
valid configuration.
See "General Memory
Module Installation
Guidelines" on page 67.
Read fault.
Requested sector
not found.
The operating system cannot
read from the hard drive,
optical drive, or USB device,
the system could not find a
particular sector on the disk,
or the requested sector is
defective.
Replace the optical medium,
USB medium, or USB
device. Ensure that the USB
cables, SAS/SATA backplane
cables, or optical drive cables
are properly connected.
See "Troubleshooting an
Optical Drive" on page 99, or
"Troubleshooting a Hard
Drive" on page 100 for the
appropriate drive(s) installed
in your system.
SATA Port
x
device not
found.
There is no device connected
to the specified SATA port.
Information only.
Table 1-4.
System Messages
(continued)
Message
Causes
Corrective Actions