Maytag MHWZ600TE Use and Care Guide - Page 10

Installation, Instructions

Get Maytag MHWZ600TE - Epic Z Front Load Washer PDF manuals and user guides
UPC - 883049141138
View all Maytag MHWZ600TE manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

i_i_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!ii4ii_,!iiii_!ii!ii[_ii!_ii!i!i_!!!_iiii_iii!}iiii}__!!i!ii_i_i_!ii}i_i_i_!iiii_!ii_ii_!!!i_iiii_ii!iii}i_i_!i!jii_ii_!_!i!ii_i_ii!iii!i_!i__!_i!i_i!!_i!!_i_!!_!__i!i!__1!!_!i_!!_i!_i!ii!!_{_i!i_i!!ii!_!_!_!ji!i!_i!!_!i)_!i_i!_!_:!i__!_!!__!!!i_[!i!i_i!_!j!i_i i_[ii!_.!_!i_i!!i_i!!_j!j_ii!_!_iii!i_ji i!!_i l!!l_!!!¸_i INSTALLATION INSTRUCTIONS Excessive Weight Hazard Use two or more people to move and install washer. Failure to do so can result in back or other injury. IMPORTANT: Position the washer so that the rear of the washer is within approximately 3 ft (90 cm) of its final location. There are 4 blue bolts in the rear panel of the washer that support the suspension system during transportation. These bolts also retain the power cord inside the washer until the bolts are removed. Insert new flat washers (supplied) into each end of the inlet hoses. Firmly seat the washers in the couplings. A B A. C_;upling B. Washer Connect the inlet hosesto the water faucets Make sure the washer drum is empty. 1. Attach a hose to the hot water faucet. Screw on coupling washen by hand until it is seated on the 2. Attach a hose to the cold water faucet. Screw on coupling by hand until it is seated on the washen 3. Using pliers, tighten the couplings with an additional two-thirds turn. 1. Using a 13 mm wrench, loosen each of the bolts. 2. Once the bolt is loose, move it to the center of the hole and completely including the plastic spacer covering the bolt. pull out the bolt, NOTE: Do not overtighten or use tape or sealants on the valve. [Damage to the valves can result. 3. Once all 4 bolts are removed, discard the bolts and spacers. Then pull the power cord through the opening of the rear panel and close the hole with the attached cap. 4. Close the bolt holes with the 4 transport bolt hole plugs. NOTE: If the washer is to be transported at a later date, call your local service center. [b avoid suspension and structural damage, your machine must be properly set up for relocation by a certified technician. 10

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
_!!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_![[i_i_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_!iiii_i_!iii!!_!_!_!_!_i!i!{i!_i!_!ji!!_!_!_!_!!i!i!_i_jii!_!_!_!_!_!!!!i[ii_._!ii!ii!!_jjii!_!iiiiji!!_!_!_!_!_!!i!i_}_!_!_!_!_l!l!!!i!!!_
4_,
i!i[ii_!!!!_iiiiii}ii}_!!i_i_}_i_iii_!ii_!!!_iiiiii}_!iji_!_!i_ii!ii!_!_!_!_i!_ii_1!_!_!_i!i!ii!!_iii!i)ii_:i_!_i[ii_i_!!_
_!_i!_!_!_!!i!i!ii!!_ii!!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_
ΒΈ
INSTALLATION
INSTRUCTIONS
Excessive
Weight
Hazard
Use
two
or more
people
to
move
and
install
washer.
Failure
to do so can
result
in back
or other
injury.
IMPORTANT:
Position
the washer
so that
the
rear of the
washer
is within
approximately
3 ft
(90 cm)
of
its final
location.
There
are 4 blue
bolts
in the
rear panel
of the washer
that
support
the
suspension
system
during
transportation.
These
bolts
also
retain
the
power
cord
inside
the washer
until
the
bolts
are removed.
1.
Using
a 13 mm
wrench,
loosen
each
of the
bolts.
2.
Once
the
bolt
is loose,
move
it to the
center
of the
hole
and
completely
pull
out
the
bolt,
including
the
plastic
spacer
covering
the
bolt.
Insert
new
flat washers
(supplied)
into
each
end
of the
inlet
hoses.
Firmly
seat the washers
in
the
couplings.
A
B
A.
C_;upling
B. Washer
Connect the inlet
hoses
to the water faucets
Make
sure
the washer
drum
is empty.
1.
Attach
a hose to the
hot
water
faucet.
Screw
on coupling
by hand
until
it is seated
on
the
washen
2.
Attach
a hose to the cold
water
faucet.
Screw
on
coupling
by hand
until
it is seated
on the
washen
3.
Using
pliers,
tighten
the
couplings
with
an additional
two-thirds
turn.
NOTE:
Do
not overtighten
or use tape
or sealants
on the
valve.
[Damage
to the valves
can
result.
3.
Once
all 4 bolts
are removed,
discard
the
bolts
and
spacers.
Then
pull
the
power
cord
through
the opening
of the
rear
panel
and close
the hole
with
the
attached
cap.
4.
Close
the
bolt
holes
with
the 4 transport
bolt
hole
plugs.
NOTE:
If the washer
is to be transported
at a later date,
call
your
local
service
center.
[b
avoid
suspension
and structural
damage,
your
machine
must
be properly
set up for
relocation
by a
certified
technician.
10