Maytag MHWZ600TE Use and Care Guide - Page 12

J_c¸, ¸ I9_8I

Page 12 highlights

_J_c¸'_ _IS(_¸ I9_8°I 1. Drape the power cord over the washer top. 2. Move the washer to its final location. 3. Place the drain hose in the laundry tub or standpipe as shown. See illustrations A and B. 1. Check the electrical requirements, Be sure that you have the correct electrical supply and the recommended grounding method. See "Electrical Requirements." 2. Check that all parts are now installed. [f there is an extra part, go back through the steps to see which step was skipped. 3. Check that you have all of your tools. 4. Dispose of/recycle all packaging materials. 5. Check that the water faucets are on. 6. Check for leaks around faucets and inlet hoses. 4. If the washer faucets and the drain standpipe are recessed, put the hooked end of the drain hose in the standpipe as shown. See illustration C. NOTES: • Do not force excess drain hose back into the rear of the washer. • [b avoid siphoning, do not seal the drain hose into the standpipe. I _=I =i iI r/ I +_, I 1,1++,I= I _>,= Properly leveling your washer avoids excessive noise and vibration. 1. Check the levelness of the washer by placing a level on the top edge of the washer, first side to side, then front to back. Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. If the washer is against a wail, move the washer out slightly before tipping back. [f the washer is not level, first prop the front with a wood block and adjust the feet as necessary; then prop the back and adjust feet as necessary. Repeat this step until washer is level. 2. Make sure all four feet are stable and resting on the floor. Then check that the appliance is perfectly level (use a level). 3. After the washer is level, use a 14 mm open-end wrench to turn the nuts on the feet tightly against the washer cabinet. IMPORIANT: All four feet must be tightened. If the nuts are not tight against the washer cabinet, the washer may vibrate, 4. The washer should not move front to back, side to side, or diagonally top edges. 5. Slide the washer to its final location. 6. Confirm the levelness of the washer. when pushed on its 7_ Plug into a grounded 3 prong outlet. 8. Read "Washer Use." 9. [b test and to clean your washer, measure V2 the detergent manufacturer's recommended amount of HE High Efficiency detergent for a medium-size load. Pour the detergent into the detergent dispenser. Select NORMAl, and then select START. Allow the washer to complete one whole cycle. Use only HE High Efficiency detergm_t. 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92

_J_c¸'_
_IS(_
¸ I9_8I__
° _¸¸¸/_'
_"_
1.
Drape
the power
cord
over
the
washer
top.
2.
Move
the washer
to its final
location.
3.
Place
the drain
hose
in the
laundry
tub
or standpipe
as shown.
See illustrations
A and
B.
1.
Check
the electrical
requirements,
Be sure that
you
have the
correct
electrical
supply
and
the
recommended
grounding
method.
See "Electrical
Requirements."
2.
Check
that
all parts are now
installed.
[f there
is an extra
part, go back
through
the
steps to
see which
step
was skipped.
3.
Check
that
you
have
all of your
tools.
4.
Dispose
of/recycle
all packaging
materials.
5.
Check
that
the
water
faucets
are on.
6.
Check
for
leaks around
faucets
and
inlet
hoses.
4.
If the washer
faucets
and
the drain
standpipe
are recessed,
put
the
hooked
end
of the
drain
hose
in the
standpipe
as shown.
See illustration
C.
NOTES:
Do
not
force
excess
drain
hose
back
into
the
rear of the
washer.
[b
avoid
siphoning,
do
not
seal the
drain
hose into
the
standpipe.
I
_=I
=i
iI
r/
I
+_,
I
1,1++,I=
I
_>,=
Properly
leveling
your
washer
avoids
excessive
noise
and vibration.
1.
Check
the
levelness
of the washer
by placing
a level
on the
top
edge
of the washer,
first
side
to side,
then
front
to back.
If the washer
is against
a wail,
move
the
washer
out
slightly
before
tipping
back.
[f the
washer
is not
level,
first prop
the
front
with
a wood
block
and adjust
the
feet as necessary;
then
prop
the
back
and
adjust
feet
as necessary.
Repeat
this
step until
washer
is level.
2.
Make
sure all four
feet are stable
and
resting
on the floor.
Then check
that the
appliance
is
perfectly
level
(use a level).
3.
After
the washer
is level,
use a 14
mm open-end
wrench
to turn the
nuts on the feet tightly
against
the washer
cabinet.
IMPORIANT:
All
four
feet
must
be tightened.
If the
nuts are not tight
against
the
washer
cabinet,
the
washer
may
vibrate,
4.
The washer
should
not
move
front
to back,
side to
side,
or diagonally
when
pushed
on
its
top
edges.
5.
Slide
the washer
to its final
location.
6.
Confirm
the
levelness
of the washer.
7_
8.
9.
Electrical
Shock
Hazard
Plug into
a
grounded
3 prong
outlet.
Do not remove
ground prong.
Do not
use an adapter.
Do not use an extension
cord.
Failure to
follow
these
instructions
can
result
in death,
fire,
or
electrical
shock.
Plug into
a grounded
3 prong
outlet.
Read
"Washer
Use."
[b
test and to clean
your
washer,
measure
V2
the
detergent
manufacturer's
recommended
amount
of
HE High
Efficiency
detergent
for a medium-size
load.
Pour the
detergent
into
the
detergent
dispenser.
Select
NORMAl,
and
then
select
START. Allow
the washer
to
complete
one
whole
cycle.
Use
only
HE
High
Efficiency
detergm_t.
12