Maytag MHWZ600TE Use and Care Guide - Page 23

WASHER

CARE

Cleaning

the

Door

Seal/Bellow

1,

2.

Open

the washer

door

and

remove

any clothing

or items

from

the

washer.

Inspect

the

gray colored

seal/bellow

between

the

door

opening

and the

basket

for stained

areas.

Pull back

the seal/bellow

to inspect

all areas

under

the seal/bellow

and

to check

fl, r

foreign

objects.

A

A. Seal/Bellow

3.

If stained

areas are found,

wipe

down

these

areas of the

seal/bellow,

using

the procedure

that

follows.

a)

Mix

a dilute

solution,

using

s/4 cup

(177

ml.) of

liquid

chlorine

bleach,

and

1 gal.

(3.8 I) of warm

tap water.

b)

Wipe

the seal/bellow

area with

the

dilute

solution,

using

a damp

cloth.

c)

let

stand

5 minutes.

d)

Wipe

down

area thoroughly

with

a dry

cloth

and

let the

washer

interior

air dry

with

door

open.

IMPORTANT:

•

Wear

rubber

gloves

when

cleaning

for prolonged

periods.

•

Refer to the

bleach

manufacturer's

instructions

for proper

use.

Washer

Maintenance

Procedure

This washer

has a special

cycle

that

uses higher

water

volumes

in combination

with

liquid

chlorine

bleach

to thoroughly

clean

the

inside

of the washer.

NOTES:

•

Read these

instructions

completely

before

beginning

the

cleaning

process.

•

If necessary,

the

cleaning

cycle

may be interrupted

by pressing

the

PAUSE/CANCEl.

button.

This

will

stop the cycle.

A RINSE & SPIN cycle

must

then

be run to thoroughly

rinse the

remaining

bleach

from

the

washer.

Failure

to do so will

cause

damage

to the

washer

and

clothing

added

to the

next

cycle.

Begin

procedure

1.

Open

the

washer

door

and

remove

any clothing

or items

from

the

washer.

2.

Be sure the

door

is closed.

3.

Open

the

dispenser

drawer

and

immediately

add

% cup

(160

m[)

of liquid

chlorine

bleach

to the bleach

compartment.

NOTE:

Do

not

add

any detergent

to this

cycle.

Use of

more

than

% cup

(160

mE) of

bleach

will

cause

product

damage

over

time.

4.

Be sure the

dispenser

drawer

is closed.

5.

Select

the

C[.EAN

WASHER

cycle.

6.

Press START.

NOTE:

The basket

will

rotate,

then

the

door

will

unlock,

lock

again,

and then

the cycle

will

continue.

•

The machine

will

not

fill,

but

the

basket

will

rotate

while

the washer

runs

a short

sensing

cycle.

This will

take

approximately

3 minutes.

7.

[he

cycle

will

determine

whether

clothing

or other

items

are in the

washer.

a)

If no items

are detected

in the

washer,

it will

proceed

to Step 8.

b)

If any

items

are detected

in the

washer,

all the

Cycle

lights

will

flash,

"rl."

or "F-

34"

will

be displayed,

and the

WASH

and CON[ROI.S

I.OCKED

lights

will

remain

lit. The door

will

unlock.

•

Press PAUSE/CANCEl.

to cancel

the failure

code.

Then

repeat

steps

1,2

and

6

to start

the

cycle

again.

8.

Once

the

cycle

has begun,

allow

the

cycle

to complete.

9.

After

the

cycle

is complete,

leave

the door

open

slightly,

to allow

for better

ventilation

and

drying

of washer

interior.

Always

do the

following

to

maintain

washer

freshness

•

Use only

HE High

Efficiency

detergent.

•

leave

the

door

slightly

open

after each

cycle

to allow

for better

ventilation

and

drying

of

washer

interior.

•

Repeat

the

cleaning

procedure

monthly,

using

% cup

(160

m[.) of

liquid

chlorine

bleach.

•

If the procedure

does

not sufficiently

improve

the

machine

freshness,

please

evaluate

your

installation

and

usage conditions

for other

causes.

Maytag MHWZ600TE Use and Care Guide - Page 23

Cleaning, Seal/Bellow

Page 23 highlights