Netgear DGN2200v3 DGN2200v3 User Manual

Netgear DGN2200v3 Manual

Get Netgear DGN2200v3 PDF manuals and user guides View all Netgear DGN2200v3 manuals
Add to My Manuals
Save this manual to your list of manuals

Netgear DGN2200v3 manual content summary:

  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 1
    N300 Wireless ADSL2+ Modem Router DGN2200v3 User Manual 350 East Plumeria Drive San Jose, CA 95134 USA November 2011 202-10870-01 v1.0
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 2
    N300 Wireless ADSL2+ Modem Router DGN2200v3 © 2011 NETGEAR, Inc. All rights reserved No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means without the written permission of NETGEAR, Inc.
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 3
    NETGEAR Genie Setup 19 View or Change Settings 19 Settings Description 19 Log In to the Modem Router 20 Upgrade Modem Router Firmware 21 Modem Router Interface 21 Setup Wizard 22 Manual Setup (Basic Settings 23 ADSL Settings 26 Unsuccessful Internet Connection 27 Change Password and Login
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 4
    N300 Wireless ADSL2+ Modem Router DGN2200v3 Turn Off Wireless Connectivity 30 Disable SSID Broadcast 31 Restrict Access by MAC Address 31 Wireless Security Options 31 Add Clients (Computers or Devices) to Your Network 31 Manual Method 32 Wi-Fi Protected Setup (WPS) Method 32 Wireless Settings
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 5
    Printer Sharing 75 Chapter 7 Advanced Settings WAN Setup 78 Default DMZ Server 79 Dynamic DNS 80 LAN Setup 81 LAN Setup Screen Settings 82 IP Address Reservation 82 Quality of Service (QoS 83 Advanced Wireless Settings 85 Advanced Wireless Settings 85 WPS Settings 86 Wireless Card Access
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 6
    N300 Wireless ADSL2+ Modem Router DGN2200v3 Internet LED Is Red 104 Obtaining an Internet IP Address 104 Troubleshooting PPPoE or PPPoA 104 Troubleshooting Internet Browsing 105 TCP/IP Network Not Responding 105 Test the LAN Path to Your Modem Router 105 Test the Path from Your Computer to a
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 7
    modem router The N300 Wireless ADSL2+ Modem Router DGN2200v3 provides you with an easy and secure way to set up a wireless home network with fast access to the Internet over a high-speed digital subscriber line (DSL). It has a built-in DSL modem, is compatible with all major DSL Internet service
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 8
    bottom of the modem router shows the Restore Factory Settings button, security PIN, preset login information, MAC address, and serial number. Restore Factory Settings Wi-Fi network name and password WPS Serial security number PIN MAC address Figure 1. Label on modem router bottom See Preset
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 9
    N300 Wireless ADSL2+ Modem Router DGN2200v3 Back Panel The back panel has the On/Off button and port connections as shown in the figure. ADSL USB Power Ethernet LAN On/Off Figure 2. Back panel port connections Front Panel The modem router front panel has the status LEDs and icons shown in the
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 10
    error has occurred with the device. USB device is ready to use. USB device is in use. You have a DSL connection. In technical terms, the DSL port is synchronized with an ISP's network-access device. Indicates that the modem router is negotiating the best possible speed on the DSL line. The unit is
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 11
    N300 Wireless ADSL2+ Modem Router DGN2200v3 Table 1. Front Panel LEDs (continued) Icon LED Activity WPS Solid green Blinking green Icon is on the Off WPS button Description Indicates that wireless security has been enabled. WPS-capable device is connecting to the device. WPS is not enabled.
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 12
    N300 Wireless ADSL2+ Modem Router DGN2200v3 Position Your Modem Router The modem router lets you access your network from virtually anywhere within the operating range of your wireless network. However, the operating distance or range of your wireless connection can vary significantly depending on
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 13
    N300 Wireless ADSL2+ Modem Router DGN2200v3 One-Line ADSL Microfilter Plug the ADSL microfilter into the wall outlet and plug your phone equipment into the jack labeled Phone. The modem router plugs directly into a separate DSL line. Plugging the modem router connectivity for both the modem router
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 14
    ADSL Phone N300 Wireless ADSL2+ Modem Router DGN2200v3 Cable Your Modem Router Internet Line Figure 6. Cable connections CAUTION: Incorrectly connecting a filter to your modem router blocks your DSL connection. This section includes the same information on the printed installation guide that came
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 15
    panel of the modem router. 3. Connect a computer. You can use an Ethernet cable or connect wirelessly. Internet 3 Line • Use the yellow Ethernet cable to connect your computer to an Ethernet port on your router. • Or, connect wirelessly by using the preset wireless security settings located on the
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 16
    address bar. 5. Connect any additional wired PCs to your modem router by inserting an Ethernet cable from a PC into one of the three remaining LAN ports. Note: If you are an advanced user who wants to set up the modem to run in "pure bridge" or Modem mode, you need to log in to the modem and change
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 17
    the following sections: • Modem Router Setup Preparation • NETGEAR Genie Setup • Log In to the Modem Router • Upgrade Modem Router Firmware • Modem Router Interface • Setup Wizard • Manual Setup (Basic Settings) • ADSL Settings • Unsuccessful Internet Connection • Change Password and Login Time-Out
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 18
    use manual setup. Use Standard TCP/IP Properties for DHCP If you set up your computer to use a static IP address, you have to change the settings back so that it uses Dynamic Host Configuration Protocol (DHCP). Replace an Existing Modem and Router To replace an existing modem and router, disconnect
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 19
    the instructions to complete the setup. NETGEAR Genie checks your hardware setup and guides you through connecting the modem router to the Internet and adding computers to your network. Your modem router connects to the Internet when any computer on your network launches a Web browser to access the
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 20
    3. If you are having trouble accessing the modem router wirelessly, NETGEAR recommends that during setup you use an Ethernet cable to connect your computer so that you can log in to the modem router. 4. If you cannot connect to the modem router, check the Internet Protocol (TCP/IP) properties in the
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 21
    and the Ready light has stopped blinking for several seconds. You cannot upgrade firmware until you have established your Internet connection as described in Setup Wizard on page 22. Modem Router Interface The modem router interface lets you view or change the modem router settings. The left
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 22
    N300 Wireless ADSL2+ Modem Router DGN2200v3 Note: If you go to the Advanced Device Mode screen and change the device mode setting to Modem Mode, then menu items not supported in Modem Mode will be grayed out. • Setup Wizard. Specify the language and location, and automatically detect the Internet
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 23
    . The default DSL settings usually work fine. If you have problems with your connection, check the DSL settings, and see ADSL Settings on page 26 for more information. 3. If no login is required, you can specify the MAC Address setting. 4. Click Apply to save your settings. Modem Router Setup 23
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 24
    N300 Wireless ADSL2+ Modem Router DGN2200v3 5. Click Test to test your Internet connection. If the NETGEAR website does not appear within 1 minute, and see Troubleshooting on page 100. ISP does not require login ISP does require login The following descriptions explain all of the possible fields
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 25
    disabled. 1. Disabling NAT reboots the modem router and resets its configuration settings to the factory defaults. Disable NAT only if you plan to set up the modem router in a setting where you will be manually administering the IP address space on the LAN side of the modem. Modem Router Setup 25
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 26
    N300 Wireless ADSL2+ Modem Router DGN2200v3 When no login is required, this field displays: Router MAC Address. The Ethernet MAC address used by the modem router on the Internet port. Some ISPs register the MAC address of the network interface card in your computer when your account is first opened.
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 27
    the Network Connections section of your PC Control Panel. They should be set to obtain both IP and DNS server addresses automatically. See your computer documentation. Change Password and Login Time-Out For security reasons, the modem router has its own user name and password that default to admin
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 28
    N300 Wireless ADSL2+ Modem Router DGN2200v3 The administrator's login to the modem router configuration times out after a period of inactivity to prevent someone else from accessing the modem router interface when you step away. 5. Click Apply to save your changes. After changing the password, you
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 29
    a USB port. Make sure the wireless adapter in each computer in your wireless network supports the same security settings as the modem router. See Preset Security on page 30 for information about the modem router's preconfigured security settings. Note: If you connect devices to your modem router
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 30
    here and in Chapter 4, Security Settings. • Turn off wireless connectivity • Disable SSID broadcast • Restrict access by MAC address • Wireless security options Turn Off Wireless Connectivity You can turn off the wireless connectivity of the modem router by pressing the Wireless On/Off button on its
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 31
    N300 Wireless ADSL2+ Modem Router DGN2200v3 Disable SSID Broadcast By default, the modem router broadcasts its Wi-Fi network name (SSID) so devices can find it. If you change this setting to not allow the broadcast, wireless devices will not find your modem router unless they are configured with the
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 32
    gaming device, iPhone) that you want to connect to your modem router. This software scans for all wireless networks in your area. 2. Look for your network and select it. If you did not change the name of your network during the setup process, look for the default Wi-Fi network name (SSID) and select
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 33
    new settings and save them in a secure location. Note: If you use a wireless computer to change the wireless network name (SSID) or security options, you are disconnected when you click Apply. To avoid this problem, use a computer with a wired connection to access the modem router. Wireless Settings
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 34
    N300 Wireless ADSL2+ Modem Router DGN2200v3 Consider Every Device on Your Network Before you begin, check the following: • Every wireless computer has to be able to obtain an IP address by DHCP from the modem router as described in Use Standard TCP/IP Properties for DHCP on page 18. • Each computer
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 35
    Wireless ADSL2+ Modem Router DGN2200v3 Note: The screen sections, settings, and procedures are explained in the following sections. 3. Set up and test your computers for wireless connectivity: a. Use your wireless computer or device to join your network. When prompted, enter the network password
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 36
    N300 Wireless ADSL2+ Modem Router DGN2200v3  To change the WPA Security Option and passphrase: 1. In the Security Options section, select the WPA option that you want. 2. Enter the passphrase that you want to use. It is a text string from 8 to 63 characters. 3. Click Apply.  To set up WEP security
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 37
    in your wireless adapter. Wireless adapter configuration utilities such as the one in Windows XP allow one key entry, which has to match the default key you set in the modem router. 6. Click Apply. Wireless Guest Networks A wireless guest network allows you to provide guests access to your
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 38
    N300 Wireless ADSL2+ Modem Router DGN2200v3 Allow guests to access My Local Network. If you want guests to have access to your home network instead of just Internet access, then select this check box. Enable Wireless Isolation. If this check box is selected, then wireless clients (computers or
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 39
    • Firewall Rules to Control Network Access • Port Triggering to Open Incoming Ports • Port Forwarding to Permit External Host Communications • How Port Forwarding Differs from Port Triggering • Set Up Port Forwarding to Local Servers • Set Up Port Triggering • Set the Time Zone • Schedule Services
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 40
    N300 Wireless ADSL2+ Modem Router DGN2200v3 Logs The modem router logs security-related events such as denied incoming service requests, hacker probes, and administrator logins. If you enable content filtering in the Block Sites screen, the Logs screen show you when someone on your network tries to
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 41
    N300 Wireless ADSL2+ Modem Router DGN2200v3 Examples of Log Messages Following are examples of log messages. In all cases, the log entry shows the time stamp as day, year-month-date hour:minute:second. Activation and Administration Tue, 2006-05-21 18:48:39 - NETGEAR activated [This entry indicates a
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 42
    N300 Wireless ADSL2+ Modem Router DGN2200v3 Keyword Blocking of HTTP Traffic Use keyword blocking to prevent certain types of HTTP traffic from accessing your network. The blocking can be always or according to a scheduled.  To block sites using keywords: 1. Select Security > Block Sites. 2. Select
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 43
    LAN side. • Outbound. Allow all access from the LAN side to the outside. Set Up Firewall Rules The Firewall Rules screen lets you configure custom rules to make exceptions to the default rules. Exceptions can be based on the service or application, source or destination IP addresses, and time of day
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 44
    N300 Wireless ADSL2+ Modem Router DGN2200v3 4. To open or close instant messaging, select one of the following radio buttons: • Close IM Ports. Disables instant messaging traffic. • Open IM Ports. Enables instant messaging traffic. IM ports are open by default. 5. Click Apply to save your settings.
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 45
    123." The following sequence shows the effects of the port forwarding rule you have defined: 1. The user of a remote computer opens a browser and requests a web page from www.example.com, which resolves to the public IP address of your router. The remote computer composes a web page request message
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 46
    N300 Wireless ADSL2+ Modem Router DGN2200v3 4. Your router performs Network Address Translation (NAT) on the source IP address, and sends this request message through the Internet to the remote computer, which displays the web page from www.example.com. To configure port forwarding, you need to know
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 47
    N300 Wireless ADSL2+ Modem Router DGN2200v3  To forward specific incoming protocols: 1. Select Advanced > Port Forwarding/Port Triggering to display the following screen: 2. Leave the Port Forwarding radio button selected as the service type. 3. Click Add, and the following screen displays: 4. From
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 48
    N300 Wireless ADSL2+ Modem Router DGN2200v3 3. Click the Add Custom Service button to display the following screen: 4. In the Service Name field, enter a descriptive name. 5. In the Protocol field, select the protocol. If you are unsure, select TCP/UDP. 6. In the Starting Port field, enter the
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 49
    N300 Wireless ADSL2+ Modem Router DGN2200v3 Set Up Port Triggering Port triggering is a dynamic extension of port forwarding that is useful in these cases: • More than one local computer needs port forwarding for the same application (but not simultaneously). • An application needs to open incoming
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 50
    N300 Wireless ADSL2+ Modem Router DGN2200v3 2. Select the Port Triggering radio button to display the port triggering information. 3. Clear the Disable Port Triggering check box. Note: If the Disable Port Triggering check box is selected after you configure port triggering, port triggering is
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 51
    N300 Wireless ADSL2+ Modem Router DGN2200v3 1. On the Port Triggering screen, click Add Service. The following screen displays: 2. In the Service Name field, type a descriptive service name. 3. In the Service User list, select Any (the default) to allow this service to be used by any computer on the
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 52
    N300 Wireless ADSL2+ Modem Router DGN2200v3 Set the Time Zone The modem router uses the Network Time Protocol (NTP) to obtain the current time and date from one of several network time servers on the Internet.  To set the time zone: 1. Select Security > Schedule. 2. Select your time zone. This
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 53
    N300 Wireless ADSL2+ Modem Router DGN2200v3 Schedule Services If you enabled service blocking in the Block Services screen or port forwarding in the Ports screen, you can set up a schedule for when blocking occurs or when access is not restricted.  To schedule services: 1. Select Security >
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 54
    N300 Wireless ADSL2+ Modem Router DGN2200v3 Enable Security Event Email user name and password information. • Send Alerts Immediately. Select the corresponding check box if you would like immediate notification of a significant security event, such as a known attack, port scan, or attempted access
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 55
    N300 Wireless ADSL2+ Modem Router DGN2200v3 - Time specifies the time of day to send the period, the log is automatically emailed to the specified email address. After the log is sent, it is cleared from the modem router's memory. If the modem router cannot email the log file, the log buffer might
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 56
    5 Administering your network This chapter describes the modem router settings for administering and maintaining the modem router and home network. This chapter contains the following sections: • Upgrade the Modem Router Firmware • Manually Check for Firmware Upgrades • Back Up and Manage the
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 57
    N300 Wireless ADSL2+ Modem Router DGN2200v3 Upgrade the Modem Router Firmware The modem router firmware (routing software) is stored in flash memory. By default, when you log in to your modem router, it checks the NETGEAR website for new firmware and alerts you if there is a newer version. Automatic
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 58
    N300 Wireless ADSL2+ Modem Router DGN2200v3  To stop automatic firmware checking: You can turn the automatic firmware checking off and check for firmware updates manually if you prefer. See Manually Check for Firmware Upgrades on page 58.  To turn off the automatic firmware check at login: 1.
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 59
    N300 Wireless ADSL2+ Modem Router DGN2200v3 4. Select Maintenance > Router Upgrade to display the following screen: 5. Click Browse, and locate the firmware you downloaded (the file ends in .img). 6. Click Upload to send the firmware to the modem router. When the upload is complete, your modem
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 60
    the modem router. Upon completion, the modem router reboots.  To erase the configuration: Click the Erase button to reset the modem router to its factory default settings. Erase sets the password to password, the LAN IP address to 192.168.0.1, and enables the modem router's DHCP. View Router Status
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 61
    N300 Wireless ADSL2+ Modem Router DGN2200v3 GUI Language Version. The currently selected language. Internet Port Settings MAC Address. The Ethernet MAC address of the DSL port. IP Address. The DSL port IP address. If no address is shown, the modem router cannot connect to the Internet. Network Type.
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 62
    N300 Wireless ADSL2+ Modem Router DGN2200v3 Channel. The current channel, which determines the operating frequency. Mode. The current mbps setting. Wireless AP. Indicates if the access point feature is enabled. If disabled, the Wireless LED on the front panel is off. Broadcast Name. Indicates if the
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 63
    N300 Wireless ADSL2+ Modem Router DGN2200v3 • Connection Speed. Typically, the downstream speed is faster than the upstream speed. • Line Attenuation. The line attenuation increases the farther you are physically located from your ISP's facilities. • Noise Margin. The signal-to-noise ratio, which is
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 64
    N300 Wireless ADSL2+ Modem Router DGN2200v3 Select Maintenance > Attached Devices. For each device, the table shows the IP address, the device name if available, and the Ethernet MAC address. Note that if the modem router is rebooted, the table data is lost until the modem router rediscovers the
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 65
    describes how to access and configure a USB storage drive attached to your modem router. Figure 8. USB port on rear panel. The USB port on the modem router can be used only to connect USB storage devices like flash drives or hard drives. Do not connect computers, USB modems, printers, CD drives, or
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 66
    drives and flash drives require drivers to be loaded in to the PC before the PC can access the USB device. Such USB devices do not work with the modem router. ReadySHARE Access Once you have set up your modem router, you can connect any USB storage device and share the contents with other users on
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 67
    N300 Wireless ADSL2+ Modem Router DGN2200v3 File-Sharing Scenarios You can share files on the USB drive for a wide variety of business and recreational purposes. The files can be any PC, Mac, or Linux file type including text files, Word, PowerPoint, Excel, MP3, pictures, and multimedia. USB drive
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 68
    This option supports downloading files only. USB Storage Basic Settings You can view or edit basic settings for the USB storage device attached to your modem router. Select USB > Basic Settings. The following screen displays: If you logged in to the modem router before you connected your USB device
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 69
    this button to safely remove the USB device attached to your modem router. See Safely Remove USB Drive on page 73.  To access a USB device attached to the modem router USB port: 1. Select USB > Basic Settings. The following screen displays: By default, the USB device is available to all computers
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 70
    N300 Wireless ADSL2+ Modem Router DGN2200v3 2. To access your USB device, click the share name or type \\readyshare in the address field of your Web browser. Network/device name: \\readyshare Share name: \\readyshare\USB_Storage If you logged in to the modem router before you connected your USB
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 71
    N300 Wireless ADSL2+ Modem Router DGN2200v3 USB Storage Advanced Settings To view or change advanced USB settings, select USB > Advanced Settings. The USB Storage (Advanced Settings) screen displays: You can use this screen to specify access to the USB storage device. The settings are as follows: •
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 72
    the link to change this setting. • Read/Write Access. Shows the permissions and access controls on the Network folder. Selecting All no password allows all users to access the Network folder. You are prompted to enter the same password that you use to log in to the modem router. Create a Network
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 73
    N300 Wireless ADSL2+ Modem Router DGN2200v3 Safely Remove USB Drive To unmount a USB disk drive so that no users can access it, from the USB Settings screen, click the Safely Remove USB button. This takes the drive offline. CAUTION: Unmount the USB default setting will scan for all content types.
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 74
    N300 Wireless ADSL2+ Modem Router DGN2200v3 Approved USB Devices (Advanced USB Settings) You can specify which USB devices are approved for use when connected to the modem router.  To allow only approved USB devices to be accessed: 1. Select Advanced > USB Settings. 2. Click Approved Devices. 3. On
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 75
    N300 Wireless ADSL2+ Modem Router DGN2200v3 Connect to the USB Drive from a Remote Computer To connect to the USB drive from remote computers using a Web browser, you use the modem router's Internet port IP address.  To connect to the modem router's USB drive using a Web browser: 1. First, locate
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 76
    N300 Wireless ADSL2+ Modem Router DGN2200v3 Configuring Windows 98SE and Windows ME The easiest way to get to your network properties is to go to your desktop, right-click Network Neighborhood and then select Properties. File and Printer Sharing for Microsoft Windows should be listed. If not, click
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 77
    : • WAN Setup • Dynamic DNS • LAN Setup • Quality of Service (QoS) • Advanced Wireless Settings • Remote Management • Static Routes • Universal Plug and Play • Traffic Meter • Wireless Bridging and Repeating Networks • Change the Device Mode For information about the Port Forwarding/Port Triggering
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 78
    N300 Wireless ADSL2+ Modem Router DGN2200v3 WAN Setup Select Advanced > WAN Setup to display the following screen: The following settings are available: • Disable Port Scan and DoS Protection. The firewall protects your LAN against port scans and denial of service (DoS) attacks. This protection
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 79
    it forwarded to one computer on your network. This computer is called the default DMZ server.  To assign a computer or server to be a default DMZ server: 1. In the WAN Setup screen, select the Default DMZ Server check box. 2. Type the IP address for that server and click Apply. Advanced Settings 79
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 80
    domain to its IP address and forward traffic directed at your domain to your current IP address. The modem router has a client that can connect to a Dynamic DNS service provider. Once you set up Dynamic DNS in the modem router, when your IP address changes, your modem router contacts your Dynamic
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 81
    different IP addressing scheme, you can make those changes in the LAN Setup screen. Note: If you change the LAN IP address of the modem router while connected through the browser, you are disconnected. To reconnect, open a new connection to the new IP address and log in.  To change the LAN settings
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 82
    N300 Wireless ADSL2+ Modem Router DGN2200v3 LAN Setup Screen Settings • Device Name. By default this shows the product model. You can change it if you want. • IP Address. The LAN IP address of the modem router. • IP Subnet Mask. The LAN subnet mask of the modem router. Combined with the IP address,
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 83
    N300 Wireless ADSL2+ Modem Router DGN2200v3 Note: The reserved address is not assigned until the next time the computer contacts the modem router's DHCP server. Reboot the computer or access its IP configuration to force a DHCP release and renew.  To edit or delete a reserved address entry: 1.
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 84
    N300 Wireless ADSL2+ Modem Router DGN2200v3 2. Click Setup QoS rule. The QoS Priority Rule list displays: 3. To change a rule, select its radio button, scroll down and click Edit. 4. To add a custom rule, click Add Priority Rule. 5. Click Apply to save your changes and return to the QoS Setup screen
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 85
    you make changes, click Apply. Note that the WLAN settings come from the settings you made in the Wireless Settings screen (see Wireless Settings Screen on page 33). Advanced Wireless Settings • Enable Wireless Router Radio. When this check box is selected, the modem router works as an access point
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 86
    modem router's wireless settings by using the modem router's PIN through WPS. You can manually enable the PIN function by clearing the Disable Router's PIN check box. Keep Existing Wireless Settings. By default, the Keep Existing Wireless Settings check box is selected. This allows the modem router
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 87
    N300 Wireless ADSL2+ Modem Router DGN2200v3 the wireless modem router from a wired computer or from a wireless computer that is on the access control list. The following screen displays: 4. If a wireless station that you want to add is connected to the network, select it from the Available Wireless
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 88
    of any common service port. The default is 8080, which is a common alternate for HTTP. 4. Click Apply to save your changes. To access your modem router from the Internet, type your modem router's WAN IP address in your browser's Address field, followed by a colon (:) and the custom port number. For
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 89
    N300 Wireless ADSL2+ Modem Router DGN2200v3 When you first configured your modem router, two implicit static routes were created. A default route was created with your ISP as the modem router, and a second static route was created to your local network for all 192.168.0.x addresses. With this
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 90
    the destination. Usually, a setting of 2 or 3 works. 4. Click Apply to save your changes. The Static Routes table is updated to show the new entry. Universal Plug and Play Universal Plug and Play (UPnP) helps devices, such as Internet appliances and computers, access the network and connect to other
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 91
    displays what type of port is opened and if that port is still active for each IP address. 3. To save, cancel your changes, or refresh the table: • Click Apply to save the new settings to the modem router. • Click Cancel to disregard any unsaved changes. • Click Refresh to update the portmap table
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 92
    N300 Wireless ADSL2+ Modem Router DGN2200v3 Traffic Meter Traffic metering allows you to monitor the volume of Internet traffic passing through your modem router's Internet port. With the Traffic Meter utility, you can set limits for traffic volume, set a monthly limit, and get a live update Download
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 93
    connection is disconnected and disabled. 7. Set up Internet Traffic Statistics to monitor the data traffic. 8. Click the Traffic Status button if you want a live update on Internet traffic status on your modem router. 9. Click Apply to save your settings. Wireless Bridging and Repeating Networks
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 94
    Repeating Function screen of the other access point you are using. • Wireless Repeater. If your modem router is the repeater, select this check box. • Repeater IP Address. If your modem router is the repeater, enter the IP address of the other access point. • Base Station MAC Address. If your modem
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 95
    N300 Wireless ADSL2+ Modem Router DGN2200v3 Set Up a Point-to-Point Bridge In point-to-point bridge mode, the modem router communicates as an access point with another bridge-mode wireless station. As a bridge, wireless client associations are disabled. Only wired clients can be connected. Use
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 96
    N300 Wireless ADSL2+ Modem Router DGN2200v3 Set Up a Multi-Point Bridge Multi-point bridge mode allows a router to bridge to multiple peer access points simultaneously. Wireless client associations are disabled. Only wired clients can be connected. Point-to-point bridge mode DGN2200 modem router
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 97
    • All access points, including your modem router, use the same SSID, channel, authentication mode, if any, and WEP security settings if security is in use. 5. Verify connectivity across the LANs. A computer on any LAN segment should be able to connect to the Internet or share files and printers with
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 98
    N300 Wireless ADSL2+ Modem Router DGN2200v3 The following figure shows an example of a repeater mode configuration. Wireless PC associated with AP 1 DGN2200 Wireless PC associated with AP 2 Internet 192.168.0.1 PCs AP 1 (parent AP in repeater mode) AP 2 in repeater mode Wireless PC associated
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 99
    N300 Wireless ADSL2+ Modem Router DGN2200v3 • The access points are on the same LAN. That is, the LAN IP addresses for the access points are in the same network. • If you are using DHCP, access point devices are set to Obtain an IP address automatically (DHCP Client) in the Basic Settings screen. •
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 100
    with your modem router. If you do not find the solution here, check the NETGEAR support site at http://support.netgear.com for product and contact information. This chapter contains the following sections: • Troubleshooting with the LEDs • Troubleshooting the Internet Connection • TCP/IP Network Not
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 101
    N300 Wireless ADSL2+ Modem Router DGN2200v3 Troubleshooting with the LEDs When you turn the power on, the power, LAN, and DSL LEDs should light as described here. If they do not, refer to the sections that follow for help. 1. When power is first applied, the Power LED lights. 2. After approximately
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 102
    defaults as explained in Factory Settings on page 109. This sets the modem router's IP address to 192.168.0.1. If the error persists, you could have a hardware problem and should contact NETGEAR Technical Support. LAN LED Is Off If the appropriate LAN LED does not light when the Ethernet connection
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 103
    N300 Wireless ADSL2+ Modem Router DGN2200v3 Troubleshooting the Internet Connection If your modem router is unable to access the Internet, you should check the ADSL connection, then the WAN TCP/IP connection. ADSL Link If your modem router is unable to access the Internet, you should first determine
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 104
    an IP address from your ISP. If your modem router is unable to obtain an IP address from the ISP, the problem might be one of the following: • If you have selected a login program, the service name, user name, or password might be incorrectly set. See the following section, Troubleshooting PPPoE
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 105
    , user name, or password. There also might be a provisioning problem with your ISP. Note: Unless you connect manually, the modem router will not authenticate using PPPoE or PPPoA until data is transmitted to the network. Troubleshooting Internet Browsing If your modem router can obtain an IP address
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 106
    instructions in LAN LED Is Off on page 102. - Check that the corresponding link LEDs are on for your network interface card and for the hub ports (if any) that are connected to your workstation and modem router. • Wrong network configuration - Verify that the Ethernet card driver software and TCP/IP
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 107
    N300 Wireless ADSL2+ Modem Router DGN2200v3 • Check that the network address of your PC (the portion of the IP address specified by the netmask) is different from the network address of the remote device. • Check that your cable or DSL modem is connected and functioning. • If your ISP assigned a
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 108
    A. Supplemental Information A This appendix includes the factory default settings and technical specifications for the N300 Wireless ADSL2+ Modem Router DGN2200v3, and instructions for wall-mounting the unit. This appendix contains the following sections: • Factory Settings • Specifications 108
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 109
    Table 3. Factory Default Settings Feature Default Behavior Router Login User login URL www.routerlogin.com or /www.routerlogin.net User name (case-sensitive) admin Login password (case-sensitive) password Internet connection WAN MAC address WAN MTU size Use default address 1492 Port speed
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 110
    N300 Wireless ADSL2+ Modem Router DGN2200v3 Table 3. Factory Default Settings (continued) Feature Wireless Wireless communication SSID name Security Broadcast SSID Country/region RF channel Operating mode Data rate Output power Access point Authentication type Wireless card access list Default
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 111
    Wireless ADSL2+ Modem Router DGN2200v3 Specifications Specification Network protocol and standards compatibility Power adapter Physical Environmental Regulatory compliance Network protocol and standards compatibility Power adapter Regulatory compliance Interface specifications Description TCP/IP
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 112
    operation and adverse action against the end-user by the applicable National regulatory authority. Note: This product's firmware limits operation to only the channels allowed in a particular Region or Country. Therefore, all options described in this user's guide may not be available in your version
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 113
    N300 Wireless ADSL2+ Modem Router DGN2200v3 Español [Spanish] Greek] Français [French] Por medio de la presente NETGEAR Inc. declara que el Radiolan cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE. NETGEAR Inc Radiolan
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 114
    User This product does not contain any user serviceable components and is to be used with approved antennas only. Any product changes NETGEAR, Inc., 350 East Plumeria Drive, San Jose, CA 95134, declare under our sole responsibility that the N300 Wireless ADSL2+ Modem Router DGN2200v3 Instructions
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 115
    N300 Wireless ADSL2+ Modem Router DGN2200v3) does not exceed the Class B limits for radio-noise emissions from digital apparatus as set go to ftp://downloads.netgear.com/files/GPLnotice.pdf. For GNU General Public License (GPL) related information, please visit http://support.netgear.com/app/answers
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 116
    N300 Wireless ADSL2+ Modem Router DGN2200v3 Interference Reduction Table The table below shows the Recommended Minimum Distance between NETGEAR equipment and household appliances to reduce interference (in feet and meters). Household Appliance Microwave ovens Baby Monitor - Analog Baby Monitor -
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 117
    forwarding) 47 D date and time 107 daylight savings time 52 default demilitarized zone (DMZ) server 79 default factory settings 109 denial of service (DoS) port scans 78 protection 39 devices, adding 31 diagnostic utilities 64 disabling firewalls 25 SIP ALG 78 SSID broadcast 31 disconnecting USB
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 118
    N300 Wireless ADSL2+ Modem Router DGN2200v3 IM ports 44 rules 43 firmware, upgrading 57, 88 at log in 21 automatic check 57 manually 58 front panel 9 LEDs described 9 G gateway IP address 25 genie, NETGEAR 19 guest networks 37 H host name 24 host, trusted 42 I installing manual setup 23 NETGEAR
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 119
    of wireless connections 12 ReadySHARE access 66 remote management 75, 87 removing USB drive 73 repeater mode with wireless client association 97 replace existing router 18 reserved IP address 82 restore configuration file 60 factory settings button 109 restricting wireless access by MAC addresses 36
  • Netgear DGN2200v3 | DGN2200v3 User Manual - Page 120
    Wireless ADSL2+ Modem Router DGN2200v3 trusted host 42 Trusted IP Address field 42 trusted wireless stations 87 turn off wireless connectivity 30 two-line ADSL microfilter 13 U Universal Plug and Play (UPnP) 90 unmounting USB drive 73 upgrading firmware 57, 88 USB file sharing 67 ReadySHARE access
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
350 East Plumeria Drive
San Jose, CA 95134
USA
November 2011
202-10870-01
v1.0
N300 Wireless ADSL2+
Modem Router DGN2200v3
User Manual