Panasonic AJ-HPM200 Operating Instructions

Panasonic AJ-HPM200 Manual

Get Panasonic AJ-HPM200 PDF manuals and user guides View all Panasonic AJ-HPM200 manuals
Add to My Manuals
Save this manual to your list of manuals

Panasonic AJ-HPM200 manual content summary:

  • Panasonic AJ-HPM200 | Operating Instructions - Page 1
    14. Operating Instructions Memory Card Portable Recorder/Player Model No. "+)1.1 Model No. "+)1.& Before operating this product, please read the instructions carefully and save this manual for future use. • AVCHD capability is available when the optional AVCHD Codec board AJ-YCX250G is
  • Panasonic AJ-HPM200 | Operating Instructions - Page 2
    AJ-HPM200P) WARNING: This equipment must be grounded. To ensure safe operation, the three-pin plug must be inserted only into a standard three a different AC plug. Please contact either a local or foreign Panasonic authorized service center for assistance in selecting an alternate AC plug. CAUTION:
  • Panasonic AJ-HPM200 | Operating Instructions - Page 3
    AJ-HPM200P) (continued) IMPORTANT SAFETY INSTRUCTIONS 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions for long periods of time. 14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged
  • Panasonic AJ-HPM200 | Operating Instructions - Page 4
    AJ-HPM200P Trade Name: Panasonic Responsible Party: Panasonic Corporation of North America One Panasonic Way, Secaucus, NJ07094 Support contact: Panasonic emission limit compliance, follow the attached installation instructions and the user must use only shielded interface cables when
  • Panasonic AJ-HPM200 | Operating Instructions - Page 5
    AJ-HPM200E) WARNING: This equipment must be earthed. To ensure safe operation, the three-pin plug must be inserted only into a standard shock, do not remove the covers. No user serviceable parts inside. Refer servicing to qualified service personnel. CAUTION: A coin type battery is installed
  • Panasonic AJ-HPM200 | Operating Instructions - Page 6
    Read this first! (For AJ-HPM200E) (continued) Caution for AC Mains Lead FOR YOUR SAFETY PLEASE until a replacement cover is obtained. A replacement fuse cover can be purchased from your local Panasonic Dealer. How to replace the fuse 1.Open the fuse compartment with a screwdriver. 2.Replace the
  • Panasonic AJ-HPM200 | Operating Instructions - Page 7
    AJ-HPM200E) (continued) EMC NOTICE FOR THE PURCHASER/USER OF THE APPARATUS 1. Applicable standards and operating environment (AJ-HPM200E) The apparatus is compliant with: • standards your apparatus supports AES/ (s) following instructions in this manual. 3. service life, please consult your dealer. 7
  • Panasonic AJ-HPM200 | Operating Instructions - Page 8
    and SDHC memory cards. • A memory card with the "P2" logo (for example the separately sold AJ-P2C064AG) is referred to as a "P2 card." • A hard disk drive (HDD) is referred to as a "hard disk." • A continuous video recording created during a single recording is referred to as a "clip." • The state
  • Panasonic AJ-HPM200 | Operating Instructions - Page 9
    Introduction Clip Management Read this first! (For AJ-HPM200P 2 Read this first! (For AJ-HPM200E 5 Accessories 14 Included Accessories 14 Optional Accessories 14 Opening and Closing the Top Panel 15 Features ...16 Control Reference Guide 19 Audio and Video Controller 19 GUI Operations
  • Panasonic AJ-HPM200 | Operating Instructions - Page 10
    87 Naming Playlists 88 Creating Playlists 89 Registering Events in a Playlist 89 Registering Events by Clip 95 Revising Registered Events 95 Saving a Playlist to a P2 Card 99 Opening a Playlist File 100 Deleting Playlist Files 101 Recording Voice-Overs 102 Preparing for Voice-Overs 102
  • Panasonic AJ-HPM200 | Operating Instructions - Page 11
    Level for the Entire Event during Event Recording 105 Changing Audio Level in an Device Mode 113 Using This Unit With a Hard Disk 114 Supported Hard Disks 114 Formatting Hard Disks 116 Exporting Data by 119 Importing Data from a Hard Disk to a P2 Card 120 Displaying Clip Thumbnails on a Hard
  • Panasonic AJ-HPM200 | Operating Instructions - Page 12
    to SD Memory Cards 183 Time Code, User Bit and CTL 185 Superimpose Screen 189 List of Compatible Input and Output Formats 190 Audio V Fade Function 192 Audio Recording Channels Selection 193 Audio Recording Channels 193 For Long and Trouble-Free Operation Condensation 194 Maintenance 194
  • Panasonic AJ-HPM200 | Operating Instructions - Page 13
    Pub- lic License (LGPL), and users are hereby informed that they have the Panasonic makes no guarantees for your recordings Please understand that Panasonic makes no guarantees for your recordings in cases where video and/or audio were not recorded as you intended due to problems with this unit, P2
  • Panasonic AJ-HPM200 | Operating Instructions - Page 14
    Codec board AJ-YCX250G ◆ NOTE: • Do not use optional boards other than the above product. • Have your supplier install optional boards. P2HD 5 Year Warranty Repair Program*1 Thank you for purchasing this Panasonic P2HD device. Register as a user for this device to receive a special service warranty
  • Panasonic AJ-HPM200 | Operating Instructions - Page 15
    Opening and Closing the Top Panel ◆NOTE: • Take care to avoid pinching your fingers when opening and closing the top panel. • Check that the card lock is set to on before closing the top panel. Never use force to close it when the lock is not set to on as this will damage the unit. Closing the top
  • Panasonic AJ-HPM200 | Operating Instructions - Page 16
    Features The AJ-HPM200 is a portable memory card recorder/player equipped with six P2 card slots and a 9-inch color LCD monitor. It allows you to record and play back audio and video in the compressed DVCPRO HD, DVCPRO50, DVCPRO, DV and AVC-Intra formats on the six P2 cards, to edit P2 card and
  • Panasonic AJ-HPM200 | Operating Instructions - Page 17
    Built-in up/down/cross converter for output and up converter for input The AJ-HPM200 provides a built-in up/down/cross converter for output as standard. It also up-converts composite and SD-SDI input signals to record in the same HD format as the system. ◆ NOTE: • The cross converter function is not
  • Panasonic AJ-HPM200 | Operating Instructions - Page 18
    A player using P2 cards or a hard disk can display player thumbnails. Thumbnails can be set to limit the clips used by the player to the required clips. ■ Audio AES/EBU input and output supported (16 bit, 48 kbps/4 ch) The unit comes with a 4-channel AES/EBU input and output interface as standard
  • Panasonic AJ-HPM200 | Operating Instructions - Page 19
    Guide Audio and Video Controller POWER ON 1 24 22 20 18 16 14 23 21 19 17 15 13 12 11 OFF METER 2 FULL/FINE MONITOR 3 SELECT METER SELECT CH 1-4 CH 5-8 4 PLAYER : FINE mode: Selects the standard scale (- ∞ to 0 dB 7]➝[CH8 / 8]➝ (selectable only with HD [CH5+6 / 5+6]➝ format) [CH7+8
  • Panasonic AJ-HPM200 | Operating Instructions - Page 20
    setup menu No. 020 (SYS FORMAT) is set to 1080i or 720p automatically up-converts SD to HD when recording. The unit indicates this as CMPST (U/C) and SDSDI (U/C). Press the AUDIO button to open a screen 143). 7. POWER indicator Lights when the power is on. 20 Introduction: Control Reference Guide
  • Panasonic AJ-HPM200 | Operating Instructions - Page 21
    beginning of the next clip or the beginning of a clip or text memo. During playback of a recorder in playlist mode, the beginning of the next video event is located. The operation interrupted by this function "Buttons Used in Playlist Operations" (page 82). 21 Introduction: Control Reference Guide
  • Panasonic AJ-HPM200 | Operating Instructions - Page 22
    read by the time code reader from the P2 card. Select whether to make TC or UB )] ➝ [TC (read time code)] ➝ [UB (user bit of the read time code)]. 22.RESET/NEW button MEMO/MARKER button TEXT MEMO: MARKER: Press this button during recording and playback where you wish to enter a text memo. In Guide
  • Panasonic AJ-HPM200 | Operating Instructions - Page 23
    Introduction GUI Operations POWER ON 18 17 16 15 14 13 OFF METER FULL/FINE PLAYER STOP PREVIEW REC A.LEVEL REC CONTROL MODE MONITOR SELECT METER SELECT CH 1-4 CH 5-8 SOURCE SELECT . ➝Refer to "Making changes using the PF buttons" (page 156). 23 Introduction: Control Reference Guide
  • Panasonic AJ-HPM200 | Operating Instructions - Page 24
    - (SHIFT + TRIM -) button Hold down the SHIFT button and this button simultaneously to move to the previous recording slot position. Pressing this button when the unit is in slot 1 results in a move to slot 6. TRIM to delete the selected clip or event. 24 Introduction: Control Reference Guide
  • Panasonic AJ-HPM200 | Operating Instructions - Page 25
    ). PF2 button In recording/playback mode, press this to move to the previous recording slot position. Pressing this button In recording/playback mode recording/playback mode, press PLAYER/ SOURCE SELECT button PLAYER button Use this button to control an external device or operate a player to player/recorder.
  • Panasonic AJ-HPM200 | Operating Instructions - Page 26
    Operations" (page 82). 18.LCD panel Displays the audio level meters and the time code. ➝Refer to "LCD Panel" (page 28). 26 Introduction: Control Reference Guide
  • Panasonic AJ-HPM200 | Operating Instructions - Page 27
    the top panel. 3. P2 Card Access LEDs These LEDs indicate P2 card status. ➝For details, refer to "P2 card access LEDs and P2 card status" (page 38). 4. P2 Card Slots Insert P2 cards into these slots. Firmly Does not output any superimposed information. 27 Introduction: Control Reference Guide
  • Panasonic AJ-HPM200 | Operating Instructions - Page 28
    shows the counter and time codes. It displays CTL (relative position from the beginning), TC (read time code) and UB (user bit of the read time code). 3. Format display Indicates the set record format and the format of video recorded on an inserted P2 card. 28 Introduction: Control Reference Guide
  • Panasonic AJ-HPM200 | Operating Instructions - Page 29
    IEC61883-1, IEC61883-2 and SMPTE396M standards. Use 6-pin connectors. This connector does not support bus power. ◆ NOTE: output connector. • AVC-Intra 50 and AVC-Intra 100 recording and playback do not support input/output via the IEEE 1394 connector. • No input Introduction: Control Reference Guide
  • Panasonic AJ-HPM200 | Operating Instructions - Page 30
    AJ-YCX250G AVC codec board (optional), AVCHD material cannot be used as a player record an external time code onto P2 cards. ◆ NOTE: • The time code from the TIMECODE IN connector cannot be input when 29.97 is set in setup menu No. 25 (SYSTEM FREQ). 11.REF VIDEO IN connectors Input connectors for HD
  • Panasonic AJ-HPM200 | Operating Instructions - Page 31
    the AES/EBU standard. 14.ANALOG COMPOSITE • The selected recording format and the format of a recording on an inserted P2 card determine the and AVC-Intra 100 recording and playback do not support input/output via the recorded when IEEE1394 input is selected. 31 Introduction: Control Reference Guide
  • Panasonic AJ-HPM200 | Operating Instructions - Page 32
    AG. - The SDHC (SD High Capacity) card is a new standard, established by the SD Card Association in 2006, for large-scale memory Instructions, visit the P2 support desk at the following Web sites. For English: https://eww.pavc.panasonic.co.jp/pro-av/ • For details on recording Control Reference Guide
  • Panasonic AJ-HPM200 | Operating Instructions - Page 33
    connector and monitors audio and video from this device. PLAYER PLAYER SOURCE SELECT PLAYLIST THUMBNAIL THUMBNAIL PLAYLIST Off On STOP/ THUMBNAIL Thumbnail mode Recording/playback mode External control mode THUMBNAIL PLAYER PLAYER SOURCE SELECT PLAY/FF/ REW/SHTL THUMBNAIL PLAYLIST
  • Panasonic AJ-HPM200 | Operating Instructions - Page 34
    Menu Operations In the playlist or thumbnail mode, press the MENU button to open the menu. In the recording mode, the setup menu appears. ➝Refer to "Setup" (page 155). To perform menu operation, proceed as follows. VIDEO AUDIO TC PRESET REC VAR UNITY CH 1
  • Panasonic AJ-HPM200 | Operating Instructions - Page 35
    Introduction Using the On-screen Keyboard Using the Full Keyboard Using the Ten Keypad The full keyboard appears when necessary. Move the cursor to the character you want to enter and press the SET button. Use the cursor buttons to move the cursor. The ten keypad appears when necessary. Move
  • Panasonic AJ-HPM200 | Operating Instructions - Page 36
    Using a USB Keyboard Connect a USB keyboard to the USB host terminal, select a full keyboard or ten keypad menu to enable input from a USB keyboard. Selecting keyboard layout 1 Open the thumbnail screen. 2 Press the MENU button. 3 Use the cursor buttons to choose [THUMBNAIL] - [SET UP] - [KEYBOARD].
  • Panasonic AJ-HPM200 | Operating Instructions - Page 37
    . Press the STOP button to stop recording. Press PLAY to start playback. Recording cannot be started from the thumbnail/playlist mode. ➝For details, refer to "Control Reference Guide" (page 19). ◆ NOTE: • The P2 card access LED for a slot where a P2 card is inserted during playback of a previously
  • Panasonic AJ-HPM200 | Operating Instructions - Page 38
    . ● Visit the web site below and go to P2 support desk page for the latest information on P2 card and SD/SDHC memory cards. For English: https://eww.pavc.panasonic.co.jp/pro-av/ Dividing clips over 4 GB in length A continuous recording that is longer than the durations given below when an 8 GB
  • Panasonic AJ-HPM200 | Operating Instructions - Page 39
    (page 164). State of cards prior to loop recording Card 1 Unrecorded area Card 2 Recorded area Recording starts Recording cycle 1 A B Card 3 C Recording cycle 2 D B C Loop recording records the unrecorded areas (A  B  C order) on the P2 cards. When all unrecorded areas on the cards
  • Panasonic AJ-HPM200 | Operating Instructions - Page 40
    on P2 cards and SD memory cards For the latest information not available in the Operating Instructions of P2 cards and SD memory cards, visit the P2 support desk at the following Web sites. For English: https://eww.pavc.panasonic.co.jp/pro-av/ 40 Introduction: Recording, Playback and P2 Card
  • Panasonic AJ-HPM200 | Operating Instructions - Page 41
    DC OUT 12V 250mA R R E FUSE 250V T2.5AH M O F1 T E AC IN SIGNAL DC IN GND AJ-HPM200 (recorder rear panel) Audio and video input signals Remote 75 Ω 75 Ω termination ON termination ON HD REF IN SD REF IN Video monitor ◆ NOTE: • Synchronization with REF input at start of playback
  • Panasonic AJ-HPM200 | Operating Instructions - Page 42
    camera (VariCam: AJHDC27 series), the unit makes it possible to record HD SDI (720/ 23.98p over 59.94p) output from the camera as DVCPRO HD or AVC-Intra 720/23.98p native recording. Recording HD SDI signals from camera output 1 Connect the camera HD SDI (720/23.98p over 59.94p) output to the SDI
  • Panasonic AJ-HPM200 | Operating Instructions - Page 43
    in this mode. • The P2 card that is being recorded cannot be changed during recording. • In this mode, the remaining P2 card capacity at 60p (50p), the slowest slow-speed effect, is indicated. • When 59-23 or 60-24 is set in setup menu No. 25 (SYSTEM FREQ), movement in HD SDI video output may
  • Panasonic AJ-HPM200 | Operating Instructions - Page 44
    ENA) so that the unit will not engage the search mode unless you press the STILL/PAUSE button. • In the AVCHD mode, not like during P2 card playback, a smooth playback is not possible. ➝ Refer to "Playing Back AVCHD Clips" (page 151). Shuttle Mode (SHTL Mode) 2 Press the STILL/PAUSE button. 3 Turn
  • Panasonic AJ-HPM200 | Operating Instructions - Page 45
    this is normal and not indicative of a malfunction. • Movement in an AVC-Intra 1080/23.98p recording played back at +1.0 in shuttle mode may look unnatural. • In the AVCHD mode, not like during P2 card playback, a smooth playback is not possible. ➝ Refer to "Playing Back AVCHD Clips" (page 151). 45
  • Panasonic AJ-HPM200 | Operating Instructions - Page 46
    single data item that contains video, audio, metadata and other additional information. Normally, a clip is one shot generated from the start of recording until recording stops. A shot that spans multiple P2 cards is handled as a single clip. The thumbnail screen displays a list of thumbnails of the
  • Panasonic AJ-HPM200 | Operating Instructions - Page 47
    a clip contains a proxy attached using the AJ-HPX2700, AJ-HPX3700 or other camera. This unit cannot record proxies. 11. T Text memo indicator Indicates recorded in the 16:9 aspect ratio. This is not indicated for an HD format clip. 14. ! Incomplete clip indicator Indicates a clip spanning multiple P2
  • Panasonic AJ-HPM200 | Operating Instructions - Page 48
    the power was shut down during recording or was damaged for some other P2 card. Instead of X , ? appears to indicate that a clip is not in the P2 standard format. 16.P2 card slot, hard disk and LAN status P2 the network is running. Red indicates a problem occurred in the unit. Consult your supplier
  • Panasonic AJ-HPM200 | Operating Instructions - Page 49
    Clip Management Cursor operations in thumbnail screen Use the up, down, right and left cursor buttons to move the cursor. ◆ NOTE: • The search dial also allows you to move the cursor. ■ High-speed cursor movement and jumping • Hold down the SHIFT button and press the up or down cursor button to
  • Panasonic AJ-HPM200 | Operating Instructions - Page 50
    may be displayed as . • An AVC-Intra clip with a different SYSTEM FREQ. setting Show clips on P2 card in slot No. n ◆ NOTE: These operations can also be performed using buttons. • Press SLOT ) only clips in a format that can be recorded appear. 50 Clip Management: Thumbnail and Clip Management
  • Panasonic AJ-HPM200 | Operating Instructions - Page 51
    /day/year Day/month/year *1: The default setting for the AJ-HPM200P is "M-D-Y", and for the AJ-HPM200E is "D-M-Y". ◆ NOTE: • This setting is reflected in the date of recording shown in the clip property, the date and time of recording indicated when selecting DATE in the DATA DISPLAY, the date
  • Panasonic AJ-HPM200 | Operating Instructions - Page 52
    SORT: PROPERTY DISP.: STOP MODE: THUMBNAIL INIT: Specify the order thumbnails appear. OFF In recorded order ON Slot order (clips in the same slot appear according to date and time of recording). Specifies the items that will appear in a simplified property display on the left side of the
  • Panasonic AJ-HPM200 | Operating Instructions - Page 53
    Clip Management Thumbnail Editing 1 Attach a text memo to video you want to edit. ➝For details, refer to "Attaching Text Memos" (page 56). 2 Change thumbnail display to text memo display. Choose [THUMBNAIL] - [TEXT MEMO CLIPS] on the menu. 3 Move to the row below the text memo and move the cursor
  • Panasonic AJ-HPM200 | Operating Instructions - Page 54
    Selecting Clips Select clips for processing in the thumbnail screen as described below. VIDEO AUDIO TC PRESET REC VAR UNITY CH 1 CH 2 CH 3 CH 4 PROP TEXT MEMO INT REGEN TCG PRESET MARKER EXT THUMBNAIL PLAYLIST VIDEO A1 A2 GO TO EDIT MODE A3 A4 A.DUB SET LAST X TRIM MODE 1
  • Panasonic AJ-HPM200 | Operating Instructions - Page 55
    the cursor moves to the clip played prior to stopping. • Video and audio playback may be disrupted between clips of different formats (DVCPRO HD, DVCPRO50, DVCPRO/DV, AVC-Intra50, AVC-Intra100). This is normal and not indicative of a malfunction. • Changing the thumbnail screen to text memo display
  • Panasonic AJ-HPM200 | Operating Instructions - Page 56
    can be attached in a clip to mark a specific location. The user can attach shot marks to distinguish clips from each other. This is normal and not a malfunction. • Text memos are not recorded during LOOP REC or VFR ON recording. Playing back from text memo location 1 Press the THUMBNAIL button
  • Panasonic AJ-HPM200 | Operating Instructions - Page 57
    mark indicator on and off. ◆ NOTE: • When attaching or deleting shot marks for clips that span multiple P2 cards, be sure to load all the P2 cards that the clip is recorded on. • Shot marks cannot be added or deleted during loop recording. 57 Clip Management: Attaching Text Memos and Shot Marks
  • Panasonic AJ-HPM200 | Operating Instructions - Page 58
    Copying Clips Clips can be copied to a P2 card in any slot, a hard disk or FTP server. ◆ NOTE: • Take care not to turn off the power or remove a card during copying. Otherwise the
  • Panasonic AJ-HPM200 | Operating Instructions - Page 59
    Clip Management Deleting Clips Use the following procedure to delete a defective clip from a P2 card. 1 Open the thumbnail screen. 2 Select the clip to delete. 3 Press the MENU button. 4 Use the cursor buttons to choose [OPERATION] - [DELETE] and press the
  • Panasonic AJ-HPM200 | Operating Instructions - Page 60
    restore bad clips that have been damaged due sudden power outages during recording or for other reasons. Such clips are marked by the bad to a hard disk drive and then copied back to a P2 card. • When a 5-minute or longer DVCPRO HD or AVC Intra100 clip (10minute or longer DVCPRO50 or AVC Intra50
  • Panasonic AJ-HPM200 | Operating Instructions - Page 61
    clip. The ! mark appears when the P2 card where the clip resides is write- recording START UB: User bit value at start of recording DATE: Date recorded TIME: Time at start of recording DURATION: Clip length V_FORMAT: Clip recording format FRAME RATE: Playback frame rate REC RATE: Recording
  • Panasonic AJ-HPM200 | Operating Instructions - Page 62
    AUDIO: ACCESS: DEVICE: SHOOT: SCENARIO: NEWS: MEMO: The name a user assigns to a clip. This normally includes a GLOBAL CLIP ID. Video LAST UPDATE PERSON) Serial number of recording equipment and other information (MANUFACTURER, SERIAL NUMBER, MODEL NAME) Date when recording started and ended, etc. (
  • Panasonic AJ-HPM200 | Operating Instructions - Page 63
    latitude and longitude, enter a blank for altitude. They cannot be deleted separately. • Note that the metadata of a clip marked ! cannot be revised. Insert the P2 card with the remainder of the clip. • MEMO of metadata item to which a 100 character or larger memo has been attached cannot be revised
  • Panasonic AJ-HPM200 | Operating Instructions - Page 64
    DATA] - [USER CLIP NAME] and press the SET button. Use P2 viewer to create meta data upload files on a PC. P2 viewer allows you to use a PC for processing clips recorded on a P2 card. Download the latest version of P2 viewer from the URL given below. For English: https://eww.pavc.panasonic.co.jp
  • Panasonic AJ-HPM200 | Operating Instructions - Page 65
    "Dividing clips over 4 GB in length" (page 38) • When one recording spans multiple cards. Example of a recording on one P2 card (DVCPRO HD): REC start (start of recording) Stop (recording stop) Recording duration = 6 minutes Clip 1 Clip 2 Counter value = A Counter value = A + 1 Approx. 5 min
  • Panasonic AJ-HPM200 | Operating Instructions - Page 66
    can be set> • Use the cursor buttons to select a metadata item and press the SET button to view the information. USER CLIP NAME: Loaded USER CLIP NAME, counter value and recorded data CREATOR: Creator LAST UPDATE The person who last updated the PERSON: data SHOOT: The person who shot PLACE
  • Panasonic AJ-HPM200 | Operating Instructions - Page 67
    . 4 Select [ON] and press the SET button. This setting records the loaded metadata simultaneous with video recording. The USER CLIP NAME is attached to metadata as specified by the recording method. 5 Press the MENU button to end setup. 6 Record video on this unit. ◆ NOTE: • When [OFF] is selected
  • Panasonic AJ-HPM200 | Operating Instructions - Page 68
    /SDHC standard. SUPPORTED: Complies with SD/ SDHC NOT SUPPORTED: Does not comply with SD/SDHC Used capacity (bytes) Free space (bytes) Total capacity (bytes) The number of clips on an SD memory card when clips have been copied to an SD memory card using a proxy or a P2 camera recorder
  • Panasonic AJ-HPM200 | Operating Instructions - Page 69
    Clip Management 4 Select [YES] and press the SET button. The card is now formatted. ◆ NOTE: • To cancel formatting, select [NO] and press the SET button. • Check that no important data remains on a card before formatting since data erased by formatting cannot be recovered. 5 Press OK (SET button)
  • Panasonic AJ-HPM200 | Operating Instructions - Page 70
    1 Open the thumbnail screen. 2 Press the MENU button. 3 Use the cursor buttons to choose [OPERATION] - [FORMAT] - [SLOTn] (the number of the P2 card slot containing the card to format) and press the SET button. 4 Select [YES] and press the SET button. The card is now formatted. ◆ NOTE: •
  • Panasonic AJ-HPM200 | Operating Instructions - Page 71
    and other card information on the screen for checking. Selecting Information to Display Select whether remaining capacity or used capacity should appear in the P2 card information. 1 Open the thumbnail screen. 2 Press the MENU button. 3 Use the cursor buttons to choose [PROPERTY] - [PROPERTY SETUP
  • Panasonic AJ-HPM200 | Operating Instructions - Page 72
    SUPPORTED: NO CARD: An unformatted P2 card is inserted. This unit does not support the inserted card. No P2 card has been inserted. 1) 2) 3) P2 display so that the sum total of the remaining memory available for recording on each P2 card may not tally with the figure for the total memory. or
  • Panasonic AJ-HPM200 | Operating Instructions - Page 73
    are inserted. [RUN DOWN CARD] The maximum number of overwrites has been exceeded. [DIR ENTRY NG CARD] The P2 card directory structure is not supported. Open Detailed P2 Card Status for more information on this warning. 4 Press the EXIT button to end processing. 73 Clip Management: Checking Card
  • Panasonic AJ-HPM200 | Operating Instructions - Page 74
    to create a playlist that combines the desired audio and video sections recorded on a P2 card. The user can play back the clip sections on the playlist to check what the created footage will look like after editing. Sections of audio and video
  • Panasonic AJ-HPM200 | Operating Instructions - Page 75
    and a recorder to create a playlist that stores editing results. 4 Press the EDIT MODE (SHIFT + VIDEO) button to select overwrite editing and select all tracks. Player The player thumbnails or playback video appear on the left side of the playlist screen. Normally, clips on a P2 card are used
  • Panasonic AJ-HPM200 | Operating Instructions - Page 76
    operations other than OPERATION menu operations - Playlist name changes ([OPERATION] - [CHANGE PLAYLIST NAME]) • When something other than a P2 card is selected as the player, a cancellation of a temporary registration made using a three-point edit cannot be redone. • An undo/redo operation cancels
  • Panasonic AJ-HPM200 | Operating Instructions - Page 77
    interface is made up of four elements. Player screen Recorder screen Editing Timeline Data bar Player screen 1 The player screen consists of the player thumbnail screen that shows thumbnails and the player playback screen that shows player video *1. Use the THUMBNAIL button to switch
  • Panasonic AJ-HPM200 | Operating Instructions - Page 78
    the player is an external device, the yellow bar ( | ) indicating playback location does not appear. 2 3 1. Recorder time code indication Indicates the time code of the recorder playback location. • Displayed information TCR: UBR: CTL: IN: Indicates recorder time code. Indicates recorder user
  • Panasonic AJ-HPM200 | Operating Instructions - Page 79
    location. 2. Recorder playback screen display Displays video of recorder playback. 3. Recorder time bar player is an external device or hard disk Event whose source clip is not on a P2 card. However, a selected clip is indicated in a blue frame and has priority. ◆ NOTE: • Follow the instructions
  • Panasonic AJ-HPM200 | Operating Instructions - Page 80
    has room for the mark. 14.Seek bar Indicates the current playback position of the recorder. Next playback will start from the location indicated on the seek bar. 6. IN read-only files are indicated in gray. Slots with P2 cards that do not contain any saved files are indicated in red "-" symbol.
  • Panasonic AJ-HPM200 | Operating Instructions - Page 81
    indication Names of playlist files are indicated in white. Gray file name: Red file name: Indicates read-only files. Indicates that the P2 card storing the file has not been inserted. ◆ NOTE: • When a card does not contain files, white "------" appears. Editing Editing: Playlist Function 81
  • Panasonic AJ-HPM200 | Operating Instructions - Page 82
    10 12 8 9 7 18 19 20 21 23 OFF METER FULL/FINE PLAYER STOP PREVIEW REC A.LEVEL REC CONTROL MODE MONITOR SELECT METER SELECT CH 1-4 cursor to the last frame of the playlist +1. Use this function to set the recorder IN point when registering new events. (The IN point is then entered as Holding
  • Panasonic AJ-HPM200 | Operating Instructions - Page 83
    and the recorder screen and timeline become available. SOURCE SELECT (SHIFT + PLAYER) button Press this button and select a player from the devices (interfaces) listed in the menu that appears. Select a device with the cursor and press the SET button to use it as the source player. P2 CARD (default
  • Panasonic AJ-HPM200 | Operating Instructions - Page 84
    button ENTRY button Press to confirm trimming of IN and OUT points. IN/OUT + ENTRY buttons Hold down the IN or OUT button in the player or recorder and press the ENTRY button to set the current playback location as the IN or OUT point. CLIP ➝ LIST (SHIFT + ENTRY) button Inserts a clip
  • Panasonic AJ-HPM200 | Operating Instructions - Page 85
    and displays it on the timeline. Imports video to a P2 card from an external device (RS-422A) or hard disk used as the player. Use the REC + PLAY button during playback in the A.DUB mode to start voice-over recording. ➝Refer to "Recording Voice-Overs" (page 102). 21. PREVIEW/A LEVEL REC buttons
  • Panasonic AJ-HPM200 | Operating Instructions - Page 86
    menus given below. No.020 SYS FORMAT No.024/025 REC FMT(SD)/REC FMT(HD) No.026 PLY LST FMT For details on each menu, refer to "Setup" ( drop-frame flags in the playlist. • During playback or Edit Copy on the recorder, the time code of the video track clips is output intact and this may
  • Panasonic AJ-HPM200 | Operating Instructions - Page 87
    when creating events. Setting Auto Entry When Auto Entry is enabled, after confirming edit using the PREVIEW or REC button, the IN point of the recorder is automatically set to the location after the last frame in the edited section. 1 Press the MENU button and use the cursor buttons to choose
  • Panasonic AJ-HPM200 | Operating Instructions - Page 88
    5 Select [YES] and press the SET button. This registers an event where the start of the clip is the IN point and its end is the OUT point. Naming Playlists Use the steps below to name playlists. 1 Press the PLAY LIST button to open the playlist screen. 2 Press the MENU button. 3 Use the cursor
  • Panasonic AJ-HPM200 | Operating Instructions - Page 89
    connecting and setting up external devices, refer to "Connections" (page 112) and "External Remote Control" (page 124). ◆ NOTE: • When only the IN points for the player and the recorder are set and the player is a P2 card or hard disk, the audio and video of the event from the IN point of the
  • Panasonic AJ-HPM200 | Operating Instructions - Page 90
    player. 4 Press the PLAYER button to switch to recorder operations. The PLAYER button goes off and the right side of the screen appears in a yellow frame. 2 Press the PLAYER button to switch to player operations. The PLAYER when clips on a P2 card or hard disk are used as a player, though it is
  • Panasonic AJ-HPM200 | Operating Instructions - Page 91
    : been attached TEXT MEMO Selects clips with text memos CLIPS: SLOT CLIPS: Selects clips on P2 card in slot No. n ◆ NOTE: • To select specific clips as a player, select clips to be used from the player thumbnails and select [SELECTED CLIPS]. The clips then appear in the order they were selected
  • Panasonic AJ-HPM200 | Operating Instructions - Page 92
    will automatically create consecutive events. • The IN and OUT points for a P2 card or external device used as the player are retained after exiting the playlist mode. ◆ NOTE: • The IN and OUT points for the player and the recorder can be set in any order. • Setting the fourth point when any three
  • Panasonic AJ-HPM200 | Operating Instructions - Page 93
    PF2 ALL CLIP PF3 SHIFT PF4 2,3,4 Preview and assigning events (when the player is a P2 card) After setting the IN or OUT point, preview to check edit result on the recorder. 1 OFF METER FULL/FINE PLAYER MONITOR SELECT METER SELECT CH 1-4 CH 5-8 SOURCE SELECT COUNTER RESET INPUT SELECT
  • Panasonic AJ-HPM200 | Operating Instructions - Page 94
    Preview and assigning events (when the player is something other than a P2 card) 4 The event is recorded and appears on the timeline. After setting the IN or OUT point, preview to check edit result on the recorder. 31 OFF METER FULL/FINE PLAYER MONITOR SELECT METER SELECT CH 1-4 CH 5-8 SOURCE
  • Panasonic AJ-HPM200 | Operating Instructions - Page 95
    point is trimmed by 1 frame in + direction Before trimming Event1 Event2 Event3 A1 A2 A3 B1 B2 B3 C1 C2 C3 Simultaneous trimming of Trim player and recorder OUT points (OUT + TRIM+ button or SHIFT + OUT + TRIM+ button during A1 A2 A3 B1 B2 B3 B4 C1 C2 C3
  • Panasonic AJ-HPM200 | Operating Instructions - Page 96
    to select insert or overwrite editing. 2 Select the event to trim. Press the PLAYER button to switch to recorder operation. Use the cursor buttons to move the cursor to the event to be trimmed trimmed. • Trimming cannot be performed on a player other than a P2 card. 96 Editing: Creating Playlists
  • Panasonic AJ-HPM200 | Operating Instructions - Page 97
    SELECT IN ENTRY OUT CANCEL/PF DIAG SLOT CLIP OPERATION PF1 CLIP LIST PF2 ALL CLIP PF3 SHIFT PF4 Editing 2 1 Switch to recorder operation. Press the PLAYER button to switch to recorder operation. 2 Select the track of the event to be cut. Use the VIDEO/A1/A2/A3 (SHIFT + A1)/A4 (SHIFT + A2
  • Panasonic AJ-HPM200 | Operating Instructions - Page 98
    insert or overwrite editing. Use the EDIT MODE (SHIFT + VIDEO) button to select insert or overwrite editing. 2 Switch to recorder operation. Press the PLAYER button to switch to recorder operation. 3 Select the event to delete. Use the cursor buttons to move the cursor to the event to be deleted and
  • Panasonic AJ-HPM200 | Operating Instructions - Page 99
    and press the SET button. 4 Use the cursor buttons to select the number of the P2 card slot that will store the file and press the SET button. 5 Select [YES] playlist area of memory of the unit to a P2 card. 1 3,4,5 2 OFF METER FULL/FINE PLAYER MONITOR SELECT METER SELECT CH 1-4 CH 5-8 SOURCE
  • Panasonic AJ-HPM200 | Operating Instructions - Page 100
    playlist file stored on a P2 card to replace a playlist. 1 3,4,5,6 3,4,5 2 OFF METER FULL/FINE PLAYER MONITOR SELECT METER SELECT CH 1-4 no audio level can be imported. • Playlist files created on the AJ-SPD850, AJ-HPM100, AJHPM110 and AJ-HPS1500 are opened as read-only files. To edit such a
  • Panasonic AJ-HPM200 | Operating Instructions - Page 101
    Use the steps below to delete a playlist files stored on a P2 card. 1 Press the PLAY LIST button to open the playlist screen and press the SET button. 4 Use the cursor buttons to select the number of the P2 card slot that stores the playlist files to be deleted and press the SET button. 5 Select
  • Panasonic AJ-HPM200 | Operating Instructions - Page 102
    switched. ➝ For details on switching audio channels, refer to "Switching audio channels" (page 98). • Voice-overs cannot be recorded on players other than a P2 card. Select a P2 card as the player before start of recording. Preparing for Voice-Overs Make the required settings prior to a voice-over
  • Panasonic AJ-HPM200 | Operating Instructions - Page 103
    + GOTO) button to exit the voiceover mode. Setting recording tracks OFF METER FULL/FINE PLAYER MONITOR SELECT METER SELECT CH 1-4 CH 5-8 SOURCE SELECT the STILL/PAUSE button to start recording. The P2 card is returned to start of set preroll time and recording starts after preroll. Use the audio
  • Panasonic AJ-HPM200 | Operating Instructions - Page 104
    playback status 2,3 4 1 3 OFF METER FULL/FINE PLAYER MONITOR SELECT METER SELECT CH 1-4 CH 5-8 SOURCE SELECT button and press the PLAY button where you want to start a voice-over. This starts audio recording. Use the audio volume controls (VR) as necessary to adjust the playback sound level. 4
  • Panasonic AJ-HPM200 | Operating Instructions - Page 105
    disable the setting. Setting a Constant Audio Level for the Entire Event during Event Recording When registering a new event in a playlist, set a constant audio level for the registered audio event. 5 4 2 PLAYER STOP PREVIEW REC A.LEVEL REC SOURCE SELECT COUNTER STILL/ PLAY PAUSE REW FF
  • Panasonic AJ-HPM200 | Operating Instructions - Page 106
    is not available when the player is a hard disk or an external device. When an event has been captured to a P2 card, set the audio level and postroll playback section cannot be changed. 36 5 1 Press the PLAYER button to switch to recorder operations. 2 Set the IN point at the location where you
  • Panasonic AJ-HPM200 | Operating Instructions - Page 107
    review after setting the IN and OUT points in an event and changing the audio recording level will play back the event from start to end. To perform a playback check only of the section for a hard disk or an external device temporarily registered as a player. Editing: Setting Audio Level 107
  • Panasonic AJ-HPM200 | Operating Instructions - Page 108
    • Clip thumbnail • Clip name • Recording date • Recording time • Duration (length of source clip) • Serial number of P2 card storing the source clip • Number the cursor location. 1 5 3,5 4 2 OFF METER FULL/FINE PLAYER MONITOR SELECT METER SELECT CH 1-4 CH 5-8 SOURCE SELECT COUNTER RESET
  • Panasonic AJ-HPM200 | Operating Instructions - Page 109
    Editing 3 Use the cursor buttons to select the thumbnail that you want information about. 4 Press the MENU button. 5 Use the cursor buttons to choose [PROPERTY] and press the SET button. 1) 2) ◆ NOTE: • You can also press the PROP (SHIFT + TC PRESET) button instead of performing the operations
  • Panasonic AJ-HPM200 | Operating Instructions - Page 110
    operation. Press the PLAYER button to switch to recorder operation. 3 Use the cursor buttons to select the clip you want to review. ◆ NOTE: • Before playlist playback, insert all the P2 cards that contain events that belong to the playlist. Otherwise the playlist will not be played back normally
  • Panasonic AJ-HPM200 | Operating Instructions - Page 111
    NOTE: • The user can set a AJ-HPM100, AJ-HPM110 and AJ-HPS1500 can be loaded but cannot be used for Edit Copy. Use [FILE] - [SAVE AS] in the playlist menu to save it out under another name before Edit Copy. 1 3,4,5,6 3,4,5 2 OFF METER FULL/FINE PLAYER the number of the P2 card slot or hard disk
  • Panasonic AJ-HPM200 | Operating Instructions - Page 112
    English: https://eww.pavc.panasonic.co.jp/pro-av/ ◆ NOTE: • For details regarding connections, refer to the Operating Instructions supplied with the PC and the application software. Using the Unit as a USB Host Portable hard disk Connect a hard disk via USB 2.0 or eSATA to save P2 card data, view
  • Panasonic AJ-HPM200 | Operating Instructions - Page 113
    to USB Device Mode 1,4 POWER ON OFF METER FULL/FINE PLAYER MONITOR SELECT METER SELECT CH 1-4 CH 5-8 SOURCE SELECT COUNTER CH 1/3 2/4 PB 4 Press the MODE button to return to regular mode. ◆ NOTE: • Recording and playback are not available in the USB device mode. • In the playlist mode, the
  • Panasonic AJ-HPM200 | Operating Instructions - Page 114
    Using This Unit With a Hard Disk Supported Hard Disks This unit supports the following hard disks types. • Panasonic portable hard disk unit P2 store (AJ-PCS060G) • A hard disk that supports the USB 2.0 interface • A hard disk that supports the eSATA interface ◆ NOTE: • It may not be possible to
  • Panasonic AJ-HPM200 | Operating Instructions - Page 115
    Select clips on the playlist player to edit clips on a unsuitable environment. Please note that Panasonic accepts no liability whatsoever for may become corrupted. • Repair bad clips on P2 cards before copying them to a hard disk cables during recording or playback with the unit. Recording or playback
  • Panasonic AJ-HPM200 | Operating Instructions - Page 116
    disk deletes all data on the disk. 1 4,5,6,7 3,5 OFF METER FULL/FINE PLAYER MONITOR SELECT METER SELECT CH 1-4 CH 5-8 SOURCE SELECT COUNTER RESET INPUT SELECT Up to 23 cards can be saved to a hard disk. Data from each exported P2 card is recognized as a separate drive on a PC, etc. 1 Press the
  • Panasonic AJ-HPM200 | Operating Instructions - Page 117
    than entire cards to a hard disk. 6 Select the number of the source P2 card slot and press the SET button. Selecting ALL SLOT will result in a batch Windows PC. For English: https://eww.pavc.panasonic.co.jp/pro-av/ 2 2,4,5,6 3 OFF METER FULL/FINE PLAYER MONITOR SELECT METER SELECT CH 1-4 CH 5-8
  • Panasonic AJ-HPM200 | Operating Instructions - Page 118
    hard disk partitions and folders. A selected partition can also easily be used as a player in editing playlists. 1 Connect a hard disk. 2 Press the MENU button in makes it possible to read and write data by card (TYPE S, P2 store). PARTITION: VENDOR: MODEL: SIZE: USED: FREE CAP.: SELECTED PART
  • Panasonic AJ-HPM200 | Operating Instructions - Page 119
    to "Naming a partition" (this page).) Date and time of partition recording P2 card serial number Folder information (for a FAT type hard disk) : them as thumbnails. Such partitions/folders can also be used as a playlist player to enable editing of hard disk data. ➝Refer to "Creating Playlists" (
  • Panasonic AJ-HPM200 | Operating Instructions - Page 120
    screen and open the menu. 2 Choose [OPERATION] - [DELETE LAST PARTITION] and press the SET button. 1 Insert the P2 card that will store the imported partition. Be sure to insert a formatted P2 card. 2 Press the THUMBNAIL button to open the thumbnail display. 3 Connect the hard disk and wait until
  • Panasonic AJ-HPM200 | Operating Instructions - Page 121
    partitions. 4 Press the MENU button. 5 Use the cursor buttons to choose [OPERATION] - [COPY] and press the SET button. SET EXIT 1) 6 Select the number of the P2 card slot to which the data will be copied and press the SET button. 2) 7 Select [YES] and press the SET button. The clip will now
  • Panasonic AJ-HPM200 | Operating Instructions - Page 122
    /TIME: Date and time of partition recording VERIFY: Verify setting and result during recording ON: FINISHED Verification was successful ON: FAILED Verification failed "- -" is displayed on P2 store. OFF: No verification was performed NAME: User assigned partition name SIZE/USED/ Total
  • Panasonic AJ-HPM200 | Operating Instructions - Page 123
    stored on a hard disk. It shows information in the same way as the P2 card clip property. 1 Move the cursor to a clip in the hard disk thumbnail Video and audio playback may be disrupted between clips of different formats (DVCPRO HD, DVCPRO50, DVCPRO, DV, AVC-Intra50 and AVC-Intra100). This is
  • Panasonic AJ-HPM200 | Operating Instructions - Page 124
    any settings required for controlling a remotely connected device before switching. Indications during control of external devices In external control mode, the PLAYER lamp goes on and the unit provides the following indications. • The LED goes on to indicate external device status. • Indicates the
  • Panasonic AJ-HPM200 | Operating Instructions - Page 125
    / playback mode. 1 Enter the mode that permits control of external devices. Hold down the SHIFT button and press the PLAYER button when the unit is in the recording/playback mode. 2 Select an area for capture. • Use the following buttons to select an area for capture. IN+ENTRY Registers IN
  • Panasonic AJ-HPM200 | Operating Instructions - Page 126
    network connector (1000Base-T, 100Base-TX, 10Base-T) allows you to connect the unit to a network to transfer clips to network servers, browse Web sites, launch network services to use them. (Functions) • FTP client function enables the unit to send and receive clips • FTP/Samba server
  • Panasonic AJ-HPM200 | Operating Instructions - Page 127
    lengthen the time required for the setup screen to close since the network service will have to be restarted using a different setting. • When DHCP is [CLIENT] and press the SET button. FTP CLIENT: Item URL USER ID USER PASSWORD SSH Description Setup procedure Name or address of Enter using the
  • Panasonic AJ-HPM200 | Operating Instructions - Page 128
    to 31 characters) HTTP server setting User settings Setting Enter using the full keyboard. Initial value AJ-HPM200 ENABLE: Starts up FTP server. DISABLE: Does not start up FTP server. ENABLE: Starts up SAMBA service. DISABLE: Does not start up SAMBA service. Enter using the full keyboard
  • Panasonic AJ-HPM200 | Operating Instructions - Page 129
    settings for server service Select [USER LOGIN SETTING] and open any of the following screens to make the required settings. ■ Changing password and deleting user 1 Move the cursor to the user whose password is to be changed or deleted. ■ New user registration 1 Press the MENU button to open the
  • Panasonic AJ-HPM200 | Operating Instructions - Page 130
    LAN, client and server settings can be saved and loaded at a time (regardless of whatever screen is open). • User settings in the server setup screen and FTP USER PASSWORD in the client setup screen cannot be saved or loaded. Tools for checking operation, status indication and initialization Use the
  • Panasonic AJ-HPM200 | Operating Instructions - Page 131
    ID of logged in user Indicates whether SSH is set to ENABLE or DISABLE. 3) Media status This shows the presence or absence of P2 cards, whether or not • The date and time information displays either local time or world standard time, but depends on FTP server information. Sometimes only the year or
  • Panasonic AJ-HPM200 | Operating Instructions - Page 132
    services of the FTP server operates, if there is not a firewall in path of the connection and whether a user FTP server in the same way as clips on P2 cards. FTP thumbnail display 1 Open the FTP information displays either local time or world standard time, but depends on FTP server information
  • Panasonic AJ-HPM200 | Operating Instructions - Page 133
    server that are no longer necessary can be deleted in the same way as clips on P2 cards. ➝Refer to "Deleting Clips" (page 59). ◆ NOTE: • The FTP server FTP server. This function shows the same information in the same way as the P2 card clip property. 1 Move the cursor to the target clip in the FTP
  • Panasonic AJ-HPM200 | Operating Instructions - Page 134
    ENABLE will reduce transfer speed. • To check the result of a transfer on a computer, it may be necessary to use refresh on the computer. 5 Select a destination (P2 slot or hard disk folder) from the menu list to start writing back data. ◆ NOTE: • Depending on the number of clips on the server and
  • Panasonic AJ-HPM200 | Operating Instructions - Page 135
    : • The [SD CARD] menu appears only when an SD memory card is inserted. • SD memory card data can only be exported as full cards. Unlike P2 cards, it is not possible to export selected clips. 4 The server screen appears. Use the cursor buttons when the selected server folder appears to select
  • Panasonic AJ-HPM200 | Operating Instructions - Page 136
    including recording and playback are not available in server mode. • Although P2 cards can be inserted without problem in server mode, removing a P2 card will result in an E-30 error message. • SD memory cards cannot be accessed in server mode. FTP and Samba server services These services allow
  • Panasonic AJ-HPM200 | Operating Instructions - Page 137
    service This service allows you to access this unit using any of a variety of browsers from a computer. The browser displays the screen shown below. • P2 proxy data requires a browser that supports MPEG4 format audio and video browser. Use the browser to enter a user ID and password when access to a
  • Panasonic AJ-HPM200 | Operating Instructions - Page 138
    press the MODE button again. "MAIN MODE" will appear to indicate that you have returned to the normal operating mode. ◆ NOTE: • Operations including recording and playback are not available during browsing. • Some Web pages may not be correctly displayed. Sites may also display differently than when
  • Panasonic AJ-HPM200 | Operating Instructions - Page 139
    ■ Operations from USB keyboard Connect a USB keyboard to control the browser. Direction keys and TAB key: ENTER key: Move link focus. Use to confirm settings. Key [Alt]+[Home] [Alt]+[left] [Alt]+[right] [Ctrl]+[Tab] [Ctrl]+[Shift]+[Tab] [Ctrl]+[T] [Ctrl]+[D] [Ctrl]+[B] [F5] [Shift]+[F5] [Ctrl
  • Panasonic AJ-HPM200 | Operating Instructions - Page 140
    GB 12 GB 16 GB 32 GB Recording and playback RP-SDV04G RP-SDM04G RP Instructions, visit the Support Desk at the following Web site. For English: https://eww.pavc.panasonic.co.jp/pro-av/ • This unit supports SD memory cards formatted using the FAT12 and FAT 16 format compatible with the SD standard
  • Panasonic AJ-HPM200 | Operating Instructions - Page 141
    cancel formatting, select [NO]. SD memory card slots and access lamps Clips recorded on SD memory cards inserted in the SD/SDHC memory card slot on the AJ-HPM200 can be played back as thumbnails and video clips corded on P2 cards. ■ Access lamps Steady orange light: Card is available for reading
  • Panasonic AJ-HPM200 | Operating Instructions - Page 142
    A clip that is shorter than 10 seconds may not be possible to repair. • Indexes added during recording cannot be repaired. • Metadata is not repaired. *1: The AVCCAM Restorer is supplied with the AJ-YCX250G AVCHD codec board (optional). 142 AVCHD Recording and Playback: Using an Optional AVCHD Board
  • Panasonic AJ-HPM200 | Operating Instructions - Page 143
    regular HPM200 operations and AVCHD (optional) operations. Screen configuration is shown below. AVCHD clips are played back from the AVCHD mode thumbnail screen. Normal mode THUMBNAIL PLAY THUMBNAIL AVCHD mode MENU selection MODE button MENU MENU PLAY STOP AVCHD Recording and Playback
  • Panasonic AJ-HPM200 | Operating Instructions - Page 144
    location. 7) Duration indicator Indicates the duration of the clip at the cursor location. 8) Time indicator (➝ page 145) Depending on setting, this will show time code/user bit at start of clip recording, time of shooting, day of shooting or date and time of shooting. 144 AVCHD
  • Panasonic AJ-HPM200 | Operating Instructions - Page 145
    . TC: UB: TIME: DATE: DATE TIME: Time code User bit Shooting time Day of shooting Shooting date and time • recording displayed by the clip property. Y-M-D: M-D-Y:*1 D-M-Y:*1 Year/month/day Month/day/year Day/month/year *1:The default setting for the AJ-HPM200P is "M-D-Y", and for the AJ-HPM200E
  • Panasonic AJ-HPM200 | Operating Instructions - Page 146
    "Switching to AVCHD mode" (page 144). 2 Press the MENU button. 3 Use the cursor buttons to choose [SYSTEM INFO] and press the SET button. 146 AVCHD Recording and Playback: Using an Optional AVCHD Board
  • Panasonic AJ-HPM200 | Operating Instructions - Page 147
    was formatted in compliance with the SD and SDHC standard (SUPPORTED/NOT SUPPORTED). This indicates whether the SD memory card is recording User bit value at start of recording Date of recording and time of start of recording Displays time zone. Clip length Recording format 147 AVCHD Recording
  • Panasonic AJ-HPM200 | Operating Instructions - Page 148
    site listed below. For English: https://eww.pavc.panasonic.co.jp/pro-av/ To clear the clip metadata NAME (model name of optional board: AJ-YCX250G) • SHOOTER (shooter) • PLACE by assigning 0 to the first recorded clip. The USER CLIP NAME recording method is selectable. For details refer
  • Panasonic AJ-HPM200 | Operating Instructions - Page 149
    with the recorded metadata in the unit. (Use AVCCAM Viewer or P2 Viewer to create load data.) • Selecting whether to record metadata on an setting is [OFF]. USER CLIP NAME: You can select how to record the USER CLIP NAME. For details, refer to "Selecting method for recording USER CLIP NAME" (this
  • Panasonic AJ-HPM200 | Operating Instructions - Page 150
    USER CLIP NAME to be recorded • When clip metadata is loaded TYPE1: TYPE2: Loaded data Loaded data + button. • When clip metadata is not loaded or when loaded clip metadata is not to be recorded TYPE1: TYPE2: A 5-digit serial number assigned in shooting order A 5-digit serial number assigned in
  • Panasonic AJ-HPM200 | Operating Instructions - Page 151
    . The unit will now perform set skip operation. Recording AVCHD Material on P2 Cards Use the steps below to record AVCHD video to a P2 card in the DVCPRO HD or AVC-Intra format. ■ Preparing for recording 1 Set recording and playback format. Set the recording format (1080i/720P) to the same format as
  • Panasonic AJ-HPM200 | Operating Instructions - Page 152
    resume play is activated, dubbing starts from the resume position. 3 Press the SHIFT + REC button. Recording on the P2 card starts simultaneous with AVCHD clip playback. If the P2 card is not ready for recording or if PB FORMAT and SYS FORMAT differ, pressing the SHIFT + REC buttons will not start
  • Panasonic AJ-HPM200 | Operating Instructions - Page 153
    . 180 min. HA*1 (High image quality mode/ 1920 x 1080 pixels) HG*2 (Standard image quality mode/1920 x 1080 pixels) HE*2 (Long playing mode/1440 x 1080 pixels that does not support speed classes. *2: To record in HG and HE modes, use a speed class 2 or better SD memory card. Recording will not be
  • Panasonic AJ-HPM200 | Operating Instructions - Page 154
    FORMAT 025 REC FORMAT(HD) 028 AVCHD FMT 59.94 or 50 1080i or 720p DVCPROHD, AVC-I 100, AVC-I 50 PH, HA, HG, HE 3 Set recording audio channels. AVCHD recording uses 2 channels for recording. Use setup menu No. 774 (AVCHD A CH) toset recording channels. ■ Recording to P2 cards and SD memory cards
  • Panasonic AJ-HPM200 | Operating Instructions - Page 155
    SHIFT+REW (b) SHIFT+REW (b) SHIFT+REW (b) SHIFT+FF (a) A10 CARD READ A11 CARD WRITE SD memory card This unit can possess up to five user files, each of which can be selected from a menu setting. Setting values can be changed as necessary. ➝For details on change operations, refer to "Changing
  • Panasonic AJ-HPM200 | Operating Instructions - Page 156
    "ON") connected to the VIDEO OUT or SDI OUT connector make it possible to change settings. Change Operations 5 2,3,4 5 1,5 3 4 2,3 OFF METER FULL/FINE PLAYER MONITOR SELECT METER SELECT CH 1-4 CH 5-8 SOURCE SELECT COUNTER RESET INPUT SELECT VIDEO AUDIO NEW TC PRESET REC VAR UNITY CH 1 CH
  • Panasonic AJ-HPM200 | Operating Instructions - Page 157
    "Setup menu No. 30 (MENU LOCK)" (page 159). ➝For details on releasing the user file lock setting, refer to "Setup menu No. A03 (MENU LOCK)" (page 182). is engaged. Set MENU LOCK to OFF. 1 OFF METER FULL/FINE PLAYER MONITOR SELECT METER SELECT CH 1-4 CH 5-8 SOURCE SELECT COUNTER RESET INPUT
  • Panasonic AJ-HPM200 | Operating Instructions - Page 158
    0003 0000 | 0032 | 0064 0000 | 0128 | 0255 0 90 180 270 -32 | 0 | 32 -128 | 0 | 127 Settings and brief function description Adjusts system phase of a HD SDI output (in 13.5 ns steps). -: Advances the phase. +: Delays the phase. NOTE: • A reset does not return this setting to its factory default
  • Panasonic AJ-HPM200 | Operating Instructions - Page 159
    SUPER No. DISP. 25 SYSTEM FREQ 26 HD SYS H ADV 30 MENU LOCK Setting FR SUPER No. DISP. For AJ-HPM200P 0000 59.94 0001 0002 0003 0004 0005 0006 0007 0008 50 23.98 24 29.97 59-23 60-24 25 60-25 For AJ-HPM200E 0000 0001 0002 0003 0004 0005 0006
  • Panasonic AJ-HPM200 | Operating Instructions - Page 160
    displays in superimposed display, SETUP-MENU and other displays, sets recording formats, sets the formats that can be added to the playlist time for P2 cards is not displayed when no P2 card has been inserted. • The remaining time for SD memory cards is not displayed when an AJ-YCX250G AVCHD codec
  • Panasonic AJ-HPM200 | Operating Instructions - Page 161
    day/month/year) 7: Data and user bit However, when UB is selected with the COUNTER button, the time code is indicated after the user bit. 8: Data and CTL However 59.94Hz 50Hz 29.97Hz 59-23Hz 25Hz only 0000 1080i Specifies the recording format used by this unit. 0001 720p 0: 1080i mode (when set
  • Panasonic AJ-HPM200 | Operating Instructions - Page 162
    23.98 or 24 is selected in setup menu No. 25 (SYSTEM FREQ). DVCPRO HD recording is not available even when DVCPRO is selected if 29.97, 25, or 59 SYSTEM FREQ), No. 020 (SYS FORMAT) and No. 025 (REC FMT (HD)) settings and recording formats. Setup menu setting No.25: SYSTEM FREQ No.020: SYS FORMAT
  • Panasonic AJ-HPM200 | Operating Instructions - Page 163
    in setup menu No. 020 (SYS FORMAT) and No. 025 (REC FMT (HD)). 1: 1080/30PN (when set to 59.94 Hz)/1080/25PN (when set to (approx. 6 Mbps) NOTE: • Displayed only when an AJ-YCX250G AVCHD codec board (optional) is installed. • In 720P mode, recording is always made in PH mode. 031 OUT REF 0000
  • Panasonic AJ-HPM200 | Operating Instructions - Page 164
    or not to make loop recording. ➝For details, refer to "LOOP REC Function" (page 39). 0: Does not make loop recording 1: Makes loop recording NOTE: Turning the power off the time difference from the world standard time. Use the table below for reference in setting the time. 164 Setup: Item Settings
  • Panasonic AJ-HPM200 | Operating Instructions - Page 165
    a month with the power off. • When the precise time is required, check and reset the time before use. • When the AJ-YCX250G AVC codec board (optional) is installed, time zones recorded on the SD memory card can be set in 30 minute steps. Thus +12:45 is set as +13:00. Setup
  • Panasonic AJ-HPM200 | Operating Instructions - Page 166
    OPERATION This menu allows you to set method for engaging search dial operations, maximum shuttle speed operation, maximum speed of FF and REW operation, NEXT and PREV seek operations, display of warning messages when REF.VIDEO is not connected, PLAY delay time, battery type, display of warnings
  • Panasonic AJ-HPM200 | Operating Instructions - Page 167
    stopping signals in the SVITC information attached to HD SDI signals. 3: Set when other manufacturer's camera-recorders are used. NOTE: • Set the CONTROL switch to REMOTE. Refer to "Panasonic camera-recorders, recording formats and recording/stopping signals (Recording Mark)" on the next page before
  • Panasonic AJ-HPM200 | Operating Instructions - Page 168
    be made. Panasonic camera-recorders, recording formats and recording/stopping signals (Recording Mark) Model AJ-HDC27F,H AJ-HDX400P AJ-HDX400E AJ-HDX900 AG-HPX500 operating instructions. TYPE 2 *1: Recording Marks are not added to the HD SDI signal in default mode. *2: Only recording format
  • Panasonic AJ-HPM200 | Operating Instructions - Page 169
    1: DVCPRO 2: ORIG NOTE: • Select [OTHER] for ID data for a VTR other than a DVCPRO. • Select [ORIG] only when specific Panasonic controllers (such as AJ-A850, separately sold accessory) are connected. • When [ORIG] is selected, a STOP command transferred via 9P remote during thumbnail playback
  • Panasonic AJ-HPM200 | Operating Instructions - Page 170
    only during recording even when FREE user bit 507 EXT TC SEL 0000 0001 0002 EXT_L SLTC SVITC 59.94Hz 50Hz 23.98Hz 24Hz 29.97Hz 25Hz only Specifies the time code used when an external time code is used. 0: LTC of the TIME CODE IN connector 1: LTC data attached to serial signal input to HD
  • Panasonic AJ-HPM200 | Operating Instructions - Page 171
    internal time code generator value is recorded as the time code in the VAUX area. 0000 0001 SBC 59.94Hz 50Hz only F_RATE Selects user bits in the LTC data output by the TIME CODE OUT and HD SDI connectors or user bits in the SBC area (DVCPRO HD only) output via the IEEE 1394
  • Panasonic AJ-HPM200 | Operating Instructions - Page 172
    60-24Hz 25Hz Specifies the method for processing HD SDI input. (Available only for DVCPRO HD) 0: Records the 8 higher bits after rounding up the two lowest bits. 1: Records the signal with 8 higher bits, obtained by dynamic rounding. NOTE: Records 8 high-order bit signals after rounding off the
  • Panasonic AJ-HPM200 | Operating Instructions - Page 173
    from the video output connector. 0: Switches output automatically depending on current recording and playback format. 0001 1080i 1: 1080/59.94i or 1080/ menu No. 25 (SYSTEM FREQ). 653 Y LVL (HD) 0000 | 1000 | 1413 0.0% | 100.0% | 141.3% Adjusts the Y level of HD SDI output (- ∞ to 0 dB to +3
  • Panasonic AJ-HPM200 | Operating Instructions - Page 174
    0001 THRU 59.94Hz 23.98Hz 29.97Hz 59-23Hz only CUT&AD Specifies recording and output method for analog composite signals. 0: Records the input signal in its original form and outputs it without setup. 1: Records the signal with the 7.5% setup processing removed and outputs it with the 7.5% setup
  • Panasonic AJ-HPM200 | Operating Instructions - Page 175
    video distortion that is generated by dark areas that are about 10 IRE (70 mV) or less. NOTE: This setting is available in DVCPRO HD 720p mode recording. 0000 0001 OFF Specifies whether or not UMID data should be recorded. ON 0: UMID data is not recorded. 1: Recorded. Setup: Item Settings 175
  • Panasonic AJ-HPM200 | Operating Instructions - Page 176
    which superimposed the data or select "BLANK." • During playback of DVCPRO HD native clip, UMID becomes NO-INFO. 0000 0001 0002 0003 OFF Selects gamma LUMINANCE FILM REC mode on an AJ-HPX3000 by applying a Cineon curve to produce video appropriate for film recording. NOTE: • This setting is
  • Panasonic AJ-HPM200 | Operating Instructions - Page 177
    audio input (CH4). Specifies the standard level for audio output (CH1). Specifies the standard level for audio output (CH2). Specifies the standard level for audio output (CH3). Specifies the standard level for audio output (CH4). Specifies the input signal to be recorded on the audio CH1. 0: Audio
  • Panasonic AJ-HPM200 | Operating Instructions - Page 178
    Specifies whether or not audio data will be superimposed on HD SDI output and SD SDI ON output. 0: Audio recorded as CH1 and CH2 during dubbing from P2 cards to AVCHD. 2: Audio CH5 and 6 will be recorded a CH1 and 2. 3: Audio CH7 and 8 will be recorded a CH1 and 2. NOTE: Displayed only when an AJ
  • Panasonic AJ-HPM200 | Operating Instructions - Page 179
    AJ-HPM200P 0000 FS-20 0001 0002 FS-18 FS-12 For AJ-HPM200E 0000 0001 0002 FS-20 FS-18 FS-12 0000 OFF 0001 ON 0000 0001 OFF ON 0000 0001 0002 CH1-4 CH5-8 CH1-8 0000 0001 OFF ON Settings and brief function description Specifies the standard of the recording level controls.
  • Panasonic AJ-HPM200 | Operating Instructions - Page 180
    or not the playback sound be mixed in the voice-over. 0: Playback sound is not mixed. 1: The input and playback sound are mixed in the recording. NOTE: Press the STOP or SET button to open the subscreen to select the channels that will be mixed. To exit the subscreen, press the
  • Panasonic AJ-HPM200 | Operating Instructions - Page 181
    status, "LOCKED" appears and data cannot be saved. 0000 0001 0002 0003 0004 OFF USER2 USER3 USER4 USER5 Specifies which user files will be loaded into USER 1 and whether or not the USER 1 settings should be used in startup when the power is turned on. 0: Operation is started with the settings of
  • Panasonic AJ-HPM200 | Operating Instructions - Page 182
    item in the PF4 button. Select files from the four SD memory card files to load into the menu. This function is available only to USER 1-5 (SYSTEM) and USER 1-5. Select one of the four files on an SD memory card to write a menu setting. The write function is available only to
  • Panasonic AJ-HPM200 | Operating Instructions - Page 183
    the desired function (see below) in the load confirmation dialog that appears. SET button: Loads all SYSTEM settings and USER 1-5 data MULTI SEL Loads USER 1-5 data only (SHIFT + SET) button: EXIT: Cancels loading and returns to the previous screen 4 A completion message appears when the
  • Panasonic AJ-HPM200 | Operating Instructions - Page 184
    location (b/a) RESET button: Clears all text • A completion message appears when the write progress bar closes. SETUP-MENU MENU SD CARD WRITE FILE4 TITLE4 SYSTEM+USER FILE4 OK? YES/NO FORMAT 1 Press the MENU button, select A12 CARD FORMAT from USER1 in the SETUP menu and press the
  • Panasonic AJ-HPM200 | Operating Instructions - Page 185
    on a P2 card. INT-PRESET: Starts recording from the value set with the TC PRESET button. EXT: Records according to external TC input. 5 Use the TC PRESET button to set the start value of the time code or user bit. Setting the internal time code 45 2 1 OFF METER FULL/FINE PLAYER MONITOR
  • Panasonic AJ-HPM200 | Operating Instructions - Page 186
    selection) Reproducing the time code and user bit 4 Make the following settings in HD) connector is recorded as a time code. The LTC signal attached to the serial signal input to the SDI IN (HD) connector is recorded setting. 21 OFF METER FULL/FINE PLAYER MONITOR SELECT METER SELECT CH 1-4 CH
  • Panasonic AJ-HPM200 | Operating Instructions - Page 187
    Recorded time code VAUX area 1394 OFF HD 1394 ON HD SDI Internal OFF HD SDI Time HD SDI Time code on TIME CODE IN connector input *1 CMPST / SD SDI *6 1394 OFF HD 1394 ON HD SDI Time code 1394 OFF HD SDI Time 1394 ON HD SDI Time code is recorded if recording, the selected
  • Panasonic AJ-HPM200 | Operating Instructions - Page 188
    METER FULL/FINE PLAYER MONITOR SELECT METER recording stops, the counter shows the position relative to the start position. ◆ NOTE: When 23.98, 24, 59-23 or 60-24 is selected in setup menu No. 25 (SYSTEM FREQ), there is a 1-frame delay between playback video and CTL. 188 Setup: Time Code, User
  • Panasonic AJ-HPM200 | Operating Instructions - Page 189
    TCR TCR. UBR UBR. TCG UBG Relative location from the beginning Recorded time code data Time code data recorded in the VAUX area Recorded user bit data User bit data recorded in the VAUX area Time code data of the time code generator User bit data of the time code generator Display monitor Display
  • Panasonic AJ-HPM200 | Operating Instructions - Page 190
    to select the following input and output formats. Recording format AVC-Intra 50/100 DVCPRO HD Input signal System frequency SDI output *4 1080/59 AJ-HPX2000/2100/3000 HD-SDI (1080/23.98P over 59.94i) output *6: AJ-HDC27 series HD-SDI (variable frame-rate signal) output *7: AJ-HPX2000/2100 HD-
  • Panasonic AJ-HPM200 | Operating Instructions - Page 191
    (1080/23.98P over 59.94i) output *6: AJ-HDC27 series HD-SDI (variable frame-rate signal) output *7: AJ-HPX2000/2100 HD-SDI (720/25P over 50P) output *8: When the recording format is HD, an SD input signal is up-converted, recorded and output as HD. ➝ Refer to "INPUT SELECT buttons" (page 20). Setup
  • Panasonic AJ-HPM200 | Operating Instructions - Page 192
    a second clip generated by Edit Copy. • A clip that spans multiple P2 cards or a clip that has been automatically divided and recorded on an 8 GB P2 card Clip 1-1 Clip 1-2 Clip 1 • A clip created using the Edit Copy function on an AJ-SPD850 Event A Event B Clip 2 Settings in setup menu No.731
  • Panasonic AJ-HPM200 | Operating Instructions - Page 193
    CH2 inputs/CH3 + CH4 inputs No No No No SDI input Recorded track CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 Recorded signal CH1 input/CH2 input/CH3 input/CH4 input/CH1 + inputs/CH3 + CH4 inputs No (SD)/CH5 (HD) No (SD)/CH6 (HD) No (SD)/CH7 (HD) No (SD)/CH8 (HD) Setup: Audio Recording Channels Selection 193
  • Panasonic AJ-HPM200 | Operating Instructions - Page 194
    For Long and Trouble-Free Operation Condensation Condensation occurs due to the same principle involved when droplets of water form on a window pane of benzene, thinner or any other solvents as they may discolor or damage the coating of the unit. 194 For Long and Trouble-Free Operation: Condensation
  • Panasonic AJ-HPM200 | Operating Instructions - Page 195
    INPUT OUTPUT REF VIDEO SYSTEM 59.94 DVCPRO HD 1080/59i 1080/59i 1080/59i HD 59 Shows video system information DIAG-MENU WARNING INFO MATNO COPY OWNR POS 00001234005678BA 00B0458201000001 0 JPN :ORG :USER DATE TIME JAN-28-02 23:30:30 +03:00 UMID and Trouble-Free Operation: Error Messages 195
  • Panasonic AJ-HPM200 | Operating Instructions - Page 196
    or CANNOT REC SD recording in PH/HA mode is not available. (When an AJ-YCX250G AVCHD codec standard management Operation information or mismatched thumbnail data was recognized. continues (When an AJ over recording on a P2 card. Only 2 channels can be recorded in a voice-over recording. Operation
  • Panasonic AJ-HPM200 | Operating Instructions - Page 197
    Trouble-Free Operation Monitor display Description Deck operation LACK OF REC CAP. Displayed when a voice-over recording is attempted on a P2 card or when external device is selected for a player of the playlist and the REC button is pressed to start recording SD (When an AJ-YCX250G AVCHD codec
  • Panasonic AJ-HPM200 | Operating Instructions - Page 198
    continues DIR NG The P2 card directory structure is not supported. (* indicates the slot recording when frame rate data cannot be detected in the user bit 96 SEQUENCE data in an HD SDI input or when the input time code is not continuous. Normal recording Trouble-Free Operation: Error Messages
  • Panasonic AJ-HPM200 | Operating Instructions - Page 199
    user bits in the HD SDI input Recording is during EE or recording. Normal recording recording causes the button to temporarily light. It goes out a few seconds later and no recording is made. For Long and Trouble correct. CANNOT FORMAT! P2 card problem prevents formatting. Check P2 card. CANNOT RE
  • Panasonic AJ-HPM200 | Operating Instructions - Page 200
    . The user clip name plus the counter value can only contain up to 100 bytes. Characters in the clip name are automatically deleted when the total exceeds 100 bytes. WRITE PROTECTED! The P2 or SD value is invalid. Enter a valid value. 200 For Long and Trouble-Free Operation: Error Messages
  • Panasonic AJ-HPM200 | Operating Instructions - Page 201
    a card with suitable clips. CANNOT OPERATE WITH EXTERNAL PLAYER A.DUB is not available when an external player is Select a P2 card as a player. used. CANNOT OPERATE: "RED" A.DUB EVENT INCLUDED INPOINT IN point, operation is not possible. For Long and Trouble-Free Operation: Error Messages 201
  • Panasonic AJ-HPM200 | Operating Instructions - Page 202
    clip in the player thumbnail screen. the AJ-SPD850, AJ-HPM100, AJ-HPM110 or AJ- recorder OUT point. AVAILABLE IN INSERT MODE Select some point other than the recorder OUT point in editing. WRITE PROTECTED! The specified card is write protected. Insert write-enabled media. 202 For Long and Trouble
  • Panasonic AJ-HPM200 | Operating Instructions - Page 203
    on again. Displayed when communications from an AJ-YCX250G AVCHD codec board (optional) cannot be on other warning messages, follow the instructions given in the messages. Message This data conforms to a different standard and cannot be used. Cannot play Trouble-Free Operation: Error Messages 203
  • Panasonic AJ-HPM200 | Operating Instructions - Page 204
    problem cannot be solved by turning the unit off and turning it back on, try replacing the card as directed, or consult your supplier. Message CANNOT RECORD shorter than 3 seconds Recording that is 3 seconds or longer Recording shorte r than 3 seconds Plays back smoothly. Recording that is 3
  • Panasonic AJ-HPM200 | Operating Instructions - Page 205
    0T~99999T List of Shortcuts For Long and Trouble-Free Operation ■ When GUI display is on of multiple thumbnails (player and thumbnail operation) Selection of multiple events (recorder) Hold down the NEW Creates new playlists. *1: When an AJ-YCX250G AVCHD codec board (optional) is installed, the
  • Panasonic AJ-HPM200 | Operating Instructions - Page 206
    used as a player. Starts audio level recording of the area between the recorder IN point and OUT point. Records (dubs) playback of a playlist on a P2 card in AVCHD. *1 *1: When an AJ-YCX250G AVCHD codec point (IN). Deletes seek point (OUT). 206 For Long and Trouble-Free Operation: Error Messages
  • Panasonic AJ-HPM200 | Operating Instructions - Page 207
    Trouble-Free Operation Updating the Firmware in This Unit The firmware can be updated using either of the following two methods. (1) Customers who have registered for our P2 HD . For English: http://panasonic.biz/sav/pass_e/ (2) Customers not registered for a P2 HD 5-year warranty program Check
  • Panasonic AJ-HPM200 | Operating Instructions - Page 208
    is a semiconductor memory card designed for the DVCPRO P2 series, Panasonic's line of professional video and broadcast equipment. ■ Since the P2 format records data as files, it is ideally suited for computer processing. Video and audio are recorded in the MXF file format while the metadata (XML
  • Panasonic AJ-HPM200 | Operating Instructions - Page 209
    For English: https://eww.pavc.panasonic.co.jp/pro-av/ ■ How this unit handles metadata The metadata supported by this unit occupies a special area in the AVCD standard management file area. For this reason, using editing software and camera-recorders that do not support the metadata of this unit
  • Panasonic AJ-HPM200 | Operating Instructions - Page 210
    inches) (not including the support legs) Recording format: AVC-Intra100/AVC-Intra50/DVCPRO HD/ DVCPRO50/DVCPRO/DV/AVCHD*1 selectable Recording video signal: 1080/59.94i recorded continuously one after the other on the P2 card. • Depending on the number of the clips to be recorded, the recordable
  • Panasonic AJ-HPM200 | Operating Instructions - Page 211
    format SMPTE276M SDI output: BNC × 1, complies with SMPTE 292M/296M/ 299M during HD SDI input, complies with SMPTE 259M-C/272M-A (480/59.94i), ITU-R BT.656 LINE/MIC/MIC +48 V MIC: -60 dBu MIC+48V: Phantom +48V supported, -60 dBu Digital input: BNC × 2 (CH1/2, CH3/4) AES/EBU format
  • Panasonic AJ-HPM200 | Operating Instructions - Page 212
    Part1,Part2 Complies with SMPTE 396M AV/C Command Set supported USB 2.0: Host × 1, Device × 1 LAN: 1000BASE-T/100BASE-TX/10BASE-T × 1 eSATA: eSATA 3Gbit port × 1 Inrush current, measured according to European standard EN55103-1: 20.5 A 212 Specifications Mass and dimensions are approximate
  • Panasonic AJ-HPM200 | Operating Instructions - Page 213
    fading 76 Audio V fade function 192 AVCHD 140 Playback 151 Recording 153 AVCHD mode 144 B Browser 137 C CARD FUNCTIONS AVCHD 147 Export copy 133 External control mode 33 F Folder 119 Formatting Hard disk 116 P2 card 70 SD memory card 68, 141 FTP client functions 131 FTP server 136
  • Panasonic AJ-HPM200 | Operating Instructions - Page 214
    accidental deletion 40 Recording and playback 37 Recording times 38 Removing 39 Partition 119 Playlist 74 Creating 89 Deleting 101 Opening 100 Playing back 110 Saving 99 Playlist mode 33 Player 75, 77 Property Clip 108 Event 108 Server service Setting 128 User settings 129 Setup
  • Panasonic AJ-HPM200 | Operating Instructions - Page 215
    160 DISPLAY SEL 161 GUI OUTPUT 164 LOCAL ENA 160 LOOP REC 164 OUT REF 163 P.ON GUI 164 PLY LST FMT 163 REC FMT(HD 162 REC FMT(SD 161 REC REF 163 REMAIN SEL 160 SUPER 160 SYS FORMAT 161 VFR REC 163 DIF 180 DIF AUD OUT 181
  • Panasonic AJ-HPM200 | Operating Instructions - Page 216
    MODE 172 V LEVEL 174 VIDEO INT SG 172 WIDE SELECT 173 Y LVL(HD 173 Y LVL(SD 173 Thumbnail Menu HDD (USB or eSATA) EXPLORE 118 EXPORT 116 SETUP 121 META DATA INITIALIZE 67 LOAD 66 PROPERTY 66 RECORD 67 USER CLIP NAME 64 NETWORK EXPLORE 131 EXPORT 135 INITIALIZE 130 SETUP 127,128
  • Panasonic AJ-HPM200 | Operating Instructions - Page 217
    147 CARD STATUS 147 CLIP PROPERTY 147 META DATA 149 CARD READ 149 CLIP COUNT RESET 149 META INITIAL SET 149 META DATA PROP 149 RECORD 149 USER CLIP NAME 149 OPERATION 146 CLIP PROTECT 146 DELETE 146 PLAY SETUP 150 PB FORMAT 150 REPEAT PLAY 150 RESUME PLAY 150 SKIP MODE
  • Panasonic AJ-HPM200 | Operating Instructions - Page 218
    this waste, in accordance with national legislation. For business users in the European Union If you wish to discard 4881 e-mail: [email protected] TECHNICAL SUPPORT: Emergency 24 Hour Service Tel: 800-222-0741 e-mail: [email protected] Panasonic Canada Inc. 5770 Ambler
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
Operating Instructions
Memory Card Portable Recorder/Player
Model No.
AJ-HPM200P
Model No.
AJ-HPM200E
VQT2G72 (E)
ENGLISH
S0809T0 -P
Before operating this product, please read the instructions carefully and save this manual for future use.
• AVCHD capability is available when the optional AVCHD Codec board AJ-YCX250G is installed.
■
This product is eligible for the P2HD 5 Year
Warranty Repair Program. For details,
see page 14.