Panasonic AJ-HPM200 Operating Instructions - Page 41
Connections, Example of Connections in 23.98/24/29.97/25 Hz Mode
View all Panasonic AJ-HPM200 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 41 highlights
Connections Introduction Example of Connections in 23.98/24/ 29.97/25 Hz Mode When playing back a card recorded at a frame rate of 24 fps (25 fps), the unit is capable of converting the output to 1080/ 24 PsF (1080/25 PsF or 1080/50i) for recording on an AJHD3700 series. Shown in the figure below is an example of deck-to-deck connections. Input the following reference signals as REF input. AJ-HPM200 (source rear panel) Reference signal 23.98 Hz mode: HD REF 47.95 Hz (interlace) 24 Hz mode: HD REF 48 Hz (interlace) 25 Hz (HD)/50 Hz (HD) mode: HD REF 50 Hz (interlace) or SD REF 50 Hz (interlace) 29.97 Hz mode: HD REF 59.94 Hz (interlace) or SD REF 59.94 Hz (interlace) HD SDI OUT 75 Ω REMOTE IN/OUT termination OFF VIDEO REF VIDEO IN TIME CODE AUDIO MON CH1·2 AES/EBU CH3·4 IN SDI IN 75? IN AUTO OUT OUT L IN IN R E M O T E OUT R OUT OUT DVCPRO/DV HD SDI signal AJ-HD3700B HD (recorder rear panel) REF signal SD REF signal Remote signal (9P) REMOTE IN/OUT HD SDI IN ~AC IN FUSE 125V 5A REF IN HD ON 75 OFF SD HD SD 1 ON 75 OFF SD VIDEO OUT 2 3 WFM IN SD SDI OUT1 CH CH (SUPER) INPUT CH CH ACTIVE THROUGH OUT2 HD SDI IN OUT OUT 1 3 ACTIVE THROUGH OUT 2 CH CH OUTPUT CH CH SPARE MONITOR MONITOR (SUPER) REF OUT REMOTE IN DIGITAL AUDIO REMOTE OUT REMOTE IN/OUT CONTROL PANEL (SUPER) V/A CONTROL RS-232C PARALLEL IN/OUT (50P) AUDIO IN TIME CODE CH 1 CH 2 CH 3 CH 4 CH 5 IN PUSHOUT SIGNAL GND PUSHCH 1 AUDIO OUT PUSHCH 2 PUSHCH 3 PUSHCH 4 PUSHCUE MONITOR PUSHL PUSHR • In 23.98 Hz mode, the composite monitor video signal output by the ANALOG COMPOSITE MONITOR OUT connector does not include VITC signals. • For details on compatible input and output formats, refer to "List of Compatible Input and Output Formats" (page 190). • In 23.98/24 Hz mode, HD SDI output is delayed by approximately 2 frames relative to analog VIDEO output. • Composite video is not output in 24 Hz mode. Example of Connections for Remote Control These connections make it possible to send commands via the remote control connector to enable remote control of external devices. The playlist mode allows control of the source device to capture video directly to the timeline. Shown in the figure below is an example of deck-to-deck connections. Set the CONTROL switch on the front panel of the external device to REMOTE. Set the CONTROL switch on the front panel of this unit to LOCAL. AJ-HD1400, etc. (source rear panel) HD/SDI IN OUT1 OUT2 SD/SDI DVCPRO /DV TC HD/SD REF IN VIDEO OUT IN 1 Y PB AUDIO OUT OUT PUSH CH1 PUSH CH2 PUSH PUSH L R MONITOR PR AUDIO IN CH1 2 (SUPER) CH2 AUDIO MON OUT ENCODER REMOTE L DC OUT 12V 250mA R R E FUSE 250V T2.5AH M O F1 T E AC IN SIGNAL DC IN GND AJ-HPM200 (recorder rear panel) Audio and video input signals Remote 75 Ω 75 Ω termination ON termination ON HD REF IN SD REF IN Video monitor ◆ NOTE: • Synchronization with REF input at start of playback in 23.98/24 Hz mode may distort the first number of frames and mute sound output. Note that movement in HD SD video output at speeds other than 1x may look unnatural. VIDEO REF VIDEO IN TIME CODE AUDIO MON CH1·2 AES/EBU CH3·4 IN SDI IN 75? IN AUTO OUT OUT L R IN IN E M O T E OUT R OUT OUT DVCPRO/DV Introduction: Connections 41