Panasonic AJ-HPM200 Operating Instructions - Page 91

Editing Limiting the number of clips used as a player The player is normally composed of all clips on a P2 card that conform to the playlist format. Use the steps below to limit the player to a clip or specific clips. ◆ NOTE: • Clips not in the playlist format are indicated by red numbers and cannot be selected for playback. • This function is not available on external devices. 2 5 4 3 1 OFF METER FULL/FINE PLAYER MONITOR SELECT METER SELECT CH 1-4 CH 5-8 SOURCE SELECT COUNTER RESET INPUT SELECT VIDEO AUDIO NEW TC PRESET REC VAR UNITY CH 1 CH 2 CH 3 CH 4 PROP TEXT MEMO INT REGEN TCG PRESET MARKER EXT THUMBNAIL PLAYLIST VIDEO A1 A2 GO TO STOP PREVIEW REC A.LEVEL REC STILL/ PLAY PAUSE REW FF REVIEW 1 CLIP PLAY PREV NEXT SET EDIT MODE A3 A4 A.DUB LAST X TRIM MODE EXIT MULTI SEL MENU DELETE SLOT SELECT IN ENTRY OUT CANCEL/PF DIAG SLOT CLIP OPERATION PF1 CLIP LIST PF2 ALL CLIP PF3 SHIFT PF4 1 Switch to player operation. Press the PLAYER button to switch to player operation. 2 Display player thumbnails. During player operation, press the THUMBNAIL button to display thumbnails on the player screen. 3 Press the MENU button. 4 Use the cursor buttons to select the clip type that should appear under [THUMBNAIL]. ALL CLIP: Selects all clips SAME FORMAT Selects clips of the playlist format CLIPS: SELECTED Only uses selected clips CLIPS: MARKED Selects clips to which shot marks have CLIPS: been attached TEXT MEMO Selects clips with text memos CLIPS: SLOT CLIPS: Selects clips on P2 card in slot No. n ◆ NOTE: • To select specific clips as a player, select clips to be used from the player thumbnails and select [SELECTED CLIPS]. The clips then appear in the order they were selected. • Each press of the SLOT CLIP (SHIFT + IN) button switches the clip in the following order SELECTED ➝ SLOT1 ➝ SLOT2...SLOT6 ➝ SELECTED (only slots with cards). • Press ALL CLIP (SHIFT + OUT) to switch to ALL CLIP. 5 Press the SET button. The player screen opens and the player will now only use the selected clips. Setting IN and OUT points 1 2 3,6 OFF METER FULL/FINE PLAYER MONITOR SELECT METER SELECT CH 1-4 CH 5-8 SOURCE SELECT COUNTER RESET INPUT SELECT VIDEO AUDIO NEW TC PRESET REC VAR UNITY CH 1 CH 2 CH 3 CH 4 PROP TEXT MEMO INT REGEN TCG PRESET MARKER EXT THUMBNAIL PLAYLIST VIDEO A1 A2 GO TO STOP STILL PLAY PAUS REVIEW 1 CLIP PLAY EDIT MODE A3 A4 A.DUB SET LAST X TRIM MODE EXIT MULTI SEL MENU DELETE SLOT SELECT IN ENTRY OUT CANCEL/PF DIAG SLOT CLIP OPERATION PF1 CLIP LIST PF2 ALL CLIP PF3 SHIFT PF4 4,5,7,8 1 1 Selecting insert or overwrite editing. Use the EDIT MODE (SHIFT + VIDEO) button to select insert or overwrite editing. 2 Select tracks. Use the VIDEO/A1/A2/A3/A4 buttons to select the tracks that should be imported. The names of selected tracks are indicated in yellow on the left side of the timeline. 3 Switch to player operation. Press the PLAYER button to switch to player operation. 4 Set the IN point of the player. While looking at the player screen, hold down the IN button and press the ENTRY button at the start location of the required section to set the player IN point. A green is added to the player bar. The time code of the set IN point appears on the player screen while the IN button is held down. Editing: Creating Playlists 91